Likes: 
I have tried both process in updating the firmware of nuvi 2595 (US).
I found out that for RGN you need to be in pre-boot mode which quite difficult for some to do. But based on what I have read so far to be in pre-boot can be done in 2 ways:
1. Pressing the upper Left Hand most portion of the nuvi then presss on wait till the PC recognizes the device
or
2. Press the battery icon for ~10 sec and a new screen with a lot of data will appear; connect usb cable and device will be recognized by the PC.
My experience on using this process when I was trying to install PH firmware will make my 2595 go to endless loop reboot mode or Software Missing message.
As for copying GUPDATE.gcd process (loading in SD card in GARMIN\ directory) I do not get the same state of endless reboot loop and Software Missing message. But I assume that the firmware is updated because if I use the PH firmware, the device will just prompt a message that the sofware you are loading is older version than what is installed and all data will be cleared/erased. I just click YES.
So what is the difference?
Honestly, I do not have the answer but the second process will remove the scare of your life that your device has been "bricked." :-)
Welcome guest, is this your first visit? Click the "Create Account" button now to join.
Results 1 to 4 of 4
Hybrid View
-
5th April 2013, 02:50 AM #1Member +
- Join Date
- Mar 2013
- Location
- Manila
- Posts
- 50
- Rep Power
- 0
Difference Between RGN and Copying GUPDATE.gcd Firmware Update
-
5th April 2013, 05:42 AM #2Garmin/GPS Systems GMod.
- Join Date
- Aug 2011
- Location
- Oz.
- Posts
- 6,201
- Rep Power
- 2501
Some software will not load from GUPDATE.GCD but will if done via an *.rgn file with updater.exe in pre-boot mode. If you aren't sure what you are doing (especially cross-flashing or using modded fw) it is quite easy to brick your device using an inappropriate rgn.
It seems unlikely to successfully flash to PH on your US device using GUPDATE.GCD. Probably it did not load the PH fw at all. Did you check it on the unit's inventory or in GarminDevice.xml?'Thanking Posts' are banned. To thank someone, and/or to see hidden links and content, use the [Only registered and activated users can see links. ] button below left of the helpful post then refresh your browser [F5 key]. 'Thanking Posts' are banned.
Please don't spam. Posts serving no purpose other than to thank or to ask about hidden links are trashed or deleted, it's GPSPower's policy. Please don't spam.
[Only registered and activated users can see links. ] should make their first post as a new Intro Thread in [Only registered and activated users can see links. ].
-
5th April 2013, 06:04 AM #3Member +
- Join Date
- Mar 2013
- Location
- Manila
- Posts
- 50
- Rep Power
- 0
How can I check the inventory? And what will be the indication in the GarminDevice.xml that the load was successful or not?
Last edited by odelacruz; 5th April 2013 at 06:09 AM.
-
5th April 2013, 06:37 AM #4Garmin/GPS Systems GMod.
- Join Date
- Aug 2011
- Location
- Oz.
- Posts
- 6,201
- Rep Power
- 2501
On main page [Where to?/Map], hold the top RH corner [battery symbol] for several seconds, then press 'Next' [lower RH cnr] 9 times > 'Start Test' > 'More', the 3rd entry down is System and the second set of numbers is the system sw version.'
In GarminDevice.xml, the numbers in between <SoftwareVersion>xxx</SoftwareVersion> is the sw version.'Thanking Posts' are banned. To thank someone, and/or to see hidden links and content, use the [Only registered and activated users can see links. ] button below left of the helpful post then refresh your browser [F5 key]. 'Thanking Posts' are banned.
Please don't spam. Posts serving no purpose other than to thank or to ask about hidden links are trashed or deleted, it's GPSPower's policy. Please don't spam.
[Only registered and activated users can see links. ] should make their first post as a new Intro Thread in [Only registered and activated users can see links. ].
Reply With Quote
Bookmarks