iGO on Navigon Canada 310

**janch** · 18th July 2018, 09:40 PM

Hi guys

I'm struggling with iGO installation on Navigon Canada 310. Default navi runs from SD and I upgraded maps to 2018.Q1. So no problem with Navigon. But now I wanted to play around and I have added also Primo. I found one unlock menu where I can choose between Navigon an Primo (+all necessary progs). Unlock menu is launched on boot from SD as UpdateMe.exe with UpdateMe.nfSM file where are all paths to different programs, hoewer my interest is Primo only. I set the paths and primo starts and works perfectly but with one well known problem - no satellites are visible. Correct port is 7, baud 57600 as i checked from Navigon settings and also got the same result with iGO8 automatic detection. It's interesting that iGO8 and Primo don't complain about gps hw detection, but the satellites bar is always empty as it cannot see any. I know that this problem is well known with navigon devices and it can be solved with port splitter..I tried with it also, but I'm not really sure how to use it. I cannot set input values to 7/57600 (I can choose baud 57600, but I cannot chose port 7)

any suggestions are more than welcome..

**janch** · 19th July 2018, 08:42 PM

Ok, I figure it out..it's all about this port splitter and it's correct values (device specific). For this Navigon I had to set input to NMRX 2020 driver and baud 57600, added output to port 5 and than Start. Finally I set GPS and port values in Primo to 5 / 57600 and bingo!

Only problem is that Port splitter won't remember settings after device reset/restart. That could be really annoying..

Below is my simple unlock (SD) version if somebody ever needs it. It includes iGO primo 2.0 as this is the only stable version for this device. I have tested many, but all crashed after the language selection (even Primo 1.1 and 1.2). I also edit the script so the PortSplitter is automatically launched along with iGO Primo. But after device reset or restart, you need to manually launch port splitter - go to Explorer icon (or Total Commander) than go to folder \Storage Card\PortSplitter\ and launch Port.exe. Configure settings as described above, confirm and exit, launch Primo. Until you just power off/on device, settings will be preserved.

Yandex:

Spoiler:

Zippyshare:

Spoiler:

**stevoxxxx** · 26th July 2018, 06:10 AM

I'm trying to Navigon 70 + .Miopocket 4 designed for the Navigon 2100 there works in the root directory.

**gcourie** · 23rd July 2020, 03:46 PM

Originally Posted by janch

Ok, I figure it out..it's all about this port splitter and it's correct values (device specific). For this Navigon I had to set input to NMRX 2020 driver and baud 57600, added output to port 5 and than Start. Finally I set GPS and port values in Primo to 5 / 57600 and bingo!...

Hi,

Thank you for sharing and for the trial and error. Could you reupload the file please. On Yandex is gone and Zippyshre is geographically blocked for me.

I trying to bring this up to date with maps to gift it, and would rather stick with the original soft so the new owners don't have to jump through hoops to use it.
I haven't read the forum on this unit on how to update the original maps (if that's even possible) but I will.
In your opinion will this be a decent GPS unit with updated maps for a people that are not computer literate (I cannot test it on the road as I don't drive)

Thanks again!

**Boki** · 23rd July 2020, 09:05 PM

Originally Posted by gcourie

...Zippyshre is geographically blocked for me.

Use Opera with VPN service activated

Anyway, both uploads are dead...

**stevoxxxx** · 16th August 2020, 06:20 AM

If the Canada 310 is similar to the Navigon 2100, here's this should be working iGO8 on the SD card:

Spoiler: Download

Link renewed

**Korisnik** · 26th September 2024, 06:15 PM

Thank, it works on Navigon 92 plus

**rikeee** · 6th September 2020, 04:16 AM

For PortSplitter.exe you need to have settings.dat file when you start setup, and after that it works every time... I’m on vaccation now, but I will upload script with iGO8... all you have to do is to be pattient for two weeks

**ThePatcher** · 20th September 2020, 06:25 AM

Hi! I used Boki_Srb's link from here to get the WinCE Menu:

[Only registered and activated users can see links. ]

And stevoxxxx's iGO8 package works flawlessly on my Navigon 40 Plus! Well, except for TMC. But GPS is possible!

To (shamelessly) quote myself:

PortSplitter (or more correctly "Port.exe") needs to be started once to set the GPS-device up properly. So best to have PortSplitter as a startable app in the start menu to access it easily. Port 7 and 4800 baud seems to be correct for the 40 Plus. (And the settings are stored once you exit PortSplitter properly.)