sys.txt Descriptions

**Eric Wisely** · 28th September 2020, 03:46 AM

Hello,

I was testing both Becker 9.6.8.265850 and 9.6.8.247703 recently on my Wince 6. However I can't have 3d car or even don't have simple navigation arrow appeared on the map.

Moreover the radio will stop every few seconds without any sound until I need to touch the screen then the sound come alive again. But the sound stops again a few seconds later. I have to keep repeated touching the screen in order to have the sound.

Is this something to do with any Sys.txt that I need to input?

**Boki** · 28th September 2020, 06:05 AM

No, it is something up with your unit
Use "standard" Primo

**EvaTs** · 4th January 2021, 09:26 PM

Hi, I have question about favorites icons.
When u look map without navigate, its ok, but if u look map with set destination, u can't see yours favorites. I think is in sys problem..

Spoiler: large images

**vonica** · 28th February 2021, 04:42 PM

For who may be interested in disabling the volume slider (if accidentally you click on the icon of volume it activates the ding and os keys) I put in sys this:
[interface]
volume_slider=0
So when Primo starts the volume slider is not active anymore. I chose this because when I already set the volume mode I want to stay so without changing by accident.

**lakisdj** · 18th March 2021, 01:03 AM

What adjustment do I make so that the plane does not go out in navigation. I have a 3D and it changes alone on the plane. I only want 3d !!!

Spoiler: screenshot

**Boki** · 18th March 2021, 10:53 PM

You are using skin. All info in dedicated topic

Try to be more precise and understandable in your expression, use a translator

**ThunderRat** · 16th April 2023, 10:43 AM

Unsure if this is an iGO Primo issue or my xgody firmware but when i switch the car off the sat nav turns off. Is there a line for sys.txt to put it in standby and when i power up the car again it will go back to where i left off. Looking for easy fix rather than rewiring my power socket

I did try below line in the hope it would even stay on as this change to just more convenient for when i stop for fuel or the likes.

[power]
skip_resume_process=1
skip_suspend_process=1
powermgm_state=0

Thanks

**Norszczesny** · 16th April 2023, 05:56 PM

...the fault lies with the software of the car of course, it can be done if you have previously downloaded the system to the radio and previously removed the settings in ini, otherwise you can't do the same with stationary devices

**ThunderRat** · 16th April 2023, 10:28 PM

Sorry i should have said. This is a stand alone unit plugged into the 12v power socket

**k1w1_123** · 16th April 2023, 11:50 PM

@thunderat

These settings work for generic WinCE devices running Primo, allowing them to sleep on power off and resume when power is restored. I am not familiar with XGODY but from looking at their specs online I think its pretty likely this will work for you although the device settings screen could be hidden.

***********************************************************************

Sys.txt settings:

[interface]
shutdown_time= ;(1-9) time in seconds for automatic sleep mode when power is removed. (0) device stays on when power is removed

[power]
skip_suspend_process=1

****************************************************

Device Settings:

From the device startup screen (NOT within iGO):

Settings/Navi Path/Auto run GPS when startup - OFF
Settings/Next/Auto Start - OFF

****************************************************
BLUETOOTH

Using these settings, the Bluetooth function doesn't resume when the device wakes from sleep, so if you are using Bluetooth the device settings must be

Settings/Navi Path/Auto run GPS when startup - ON
Settings/Next/Auto Start - ON

The device settings remain the same and you have to live with a full reboot which takes a bit longer

Thread: sys.txt Descriptions

Thread Tools

Display

Advertissements

Bookmarks

Bookmarks

Posting Permissions