Thread: How to convert 3790us to 3790 Sg/My

updater.exe cant find help pls

Originally Posted by shahnowaz

updater.exe cant find help pls

Here it is ..[Only registered and activated users can see links. ]

Looks like the file was delete!!
Is the "updater.exe" the same as webupdate that can be downloaded from garmin website?
I just got nuvi 1490T and try to change its OS to enable Thai JCV.
Now I think I have rgn file ready, but don't understand how to flash it with rgn file in pre-boot mode.
Could you pls give more detail on this step?

Hi all!
I was trying to change firmware of my 3790 to Sg/Mal but none of the attempts was succesful :/
I was doing by instruction step-by-step with version 2.30 and 2.50 with no result.
Device is working properly but info shows still 3.60 "european" version and I didn't noticed any changes in software and/or funcionality.
It's just looks like firmvare remaining unchanged.
Can anybody faced something like that? Is there any solution?
I will appreciate any help or clues.
THX in advance!

Originally Posted by Kenokin

Hi all!
I was trying to change firmware of my 3790 to Sg/Mal but none of the attempts was succesful :/
I was doing by instruction step-by-step with version 2.30 and 2.50 with no result.
Device is working properly but info shows still 3.60 "european" version and I didn't noticed any changes in software and/or funcionality.
It's just looks like firmvare remaining unchanged.
Can anybody faced something like that? Is there any solution?
I will appreciate any help or clues.
THX in advance!

Is your 3790 US ?

3790US Hwid = 1101
3790Sg Hwid = 1288

After flash to Sg/My
For RGN_tool v0.44
Garmindevice.xml will show hwid= 1288

For RGN_Tool v0.60
Garmindevice.xml will show hwid = 1101

For software version ., it will show 2.20 or 2.30 (Always :: if you didn't edit f/w by manual)
If it shows swv 3.60(without manually edit) ., it means your unit did not be flashed by mod .gcd

I guess you used a mod .gcd file
and will not be flashed to nuvi if swv is the same as current swv in unit.

So you need to override swv to lower or higher than swv in your unit for .gcd file.
But you can use any swv number for rgn file.

If success :: at least you will see POIs Icon on map.
Please give more detail what you did and failed.

Originally Posted by ygps

Looks like the file was delete!!
Is the "updater.exe" the same as webupdate that can be downloaded from garmin website?
I just got nuvi 1490T and try to change its OS to enable Thai JCV.
Now I think I have rgn file ready, but don't understand how to flash it with rgn file in pre-boot mode.
Could you pls give more detail on this step?

updater.exe is not webupdater.
The other way to convert your unit without updater.exe is to use RGN_Tool to save your rgn file to a gupdate.gcd file ., remember to override swv to same number both boot and fw_all.
and not forget to delete a gupdate.gcd within .system in your unit.

Place gupdate.gcd in sd card\garmin\gupdate.gcd
turn off unit --> insert card--> turn on unit --> begin flashing.

But I advice you should have updater.exe because you need this tool for recover nuvi if you get in problem ie rebooting.

Originally Posted by aekhong

updater.exe is not webupdater.
The other way to convert your unit without updater.exe is to use RGN_Tool to save your rgn file to a gupdate.gcd file ., remember to override swv to same number both boot and fw_all.
and not forget to delete a gupdate.gcd within .system in your unit.

Place gupdate.gcd in sd card\garmin\gupdate.gcd
turn off unit --> insert card--> turn on unit --> begin flashing.

But I advice you should have updater.exe because you need this tool for recover nuvi if you get in problem ie rebooting.

Thank so much for the detail steps and for the updater.exe file.
I flashed my nuvi 1490T several times, but after it booted up it reported an error msg like "hardware problem gps is disable pls send unit to engineer of gps 2xx for repair".
After that my unit stuck at stage "Updating software for EcoRoute HD" for so long that I decided to flashed it back to its original firmware.
Do you know how to fix this kind of problem? Any suggestion?

Kenokin.,
When did your 3790 lost visibility of gmapdem.img., after went to CHN2.20 ??
Can you see the main detailed map?

turboccc converted his 3750 to CHN2.20 and he got 3D., DEM ability.

I have Nuvi 3790T European version. Could you please tell me step by step how am I to convert it to SG/MY version. You help really required, please. Thank you.