Likes: 
Reply With QuoteJust so I'm clear, when I remove the boot.bin from the rgn file, the RGN_Tool says I need something in segment 1. Then when I move the fw_all.bin to segment 1, it says "I hope you know what you are doing!" That's what you want me to do, right? (Section BD02 will be the first firmware section).
I'm so close I don't want to destroy it
Welcome guest, is this your first visit? Click the "Create Account" button now to join.
Results 21 to 30 of 43
Thread: Nuvi 265WT bricked
-
3rd June 2014, 06:21 PM #21Navigation software Moderator
- Join Date
- Sep 2011
- Location
- Belarus
- Posts
- 908
- Rep Power
- 439
Try flashing the next RGN (without boot.bin).
Also try flashing it AFTER flashing RGN with boot.bin.
It shouldn't. I'm asking if it's detected by updater.exe after reconnecting to the PC.
Originally Posted by pgardella
Last edited by kunix; 3rd June 2014 at 07:17 PM.
-
3rd June 2014, 10:34 PM #22Member
- Join Date
- May 2014
- Location
- US
- Age
- 60
- Posts
- 19
- Rep Power
- 0
-
3rd June 2014, 10:37 PM #23Navigation software Moderator
- Join Date
- Sep 2011
- Location
- Belarus
- Posts
- 908
- Rep Power
- 439
You don't need to move anything. You only need to unset specific checkboxes in RGN_Tool and save the result as RGN file.
That "know what you're doing" warning is ok to ignore.
I can make RGN files for you tomorrow if you're too afraid of it.Last edited by kunix; 3rd June 2014 at 10:40 PM.
-
3rd June 2014, 10:39 PM #24Member
- Join Date
- May 2014
- Location
- US
- Age
- 60
- Posts
- 19
- Rep Power
- 0
The Updater did detect it after I updated with the boot.bin only fw. And now, when restarting the device in pre-boot mode, it detects it again. I won't know if it allows me to update until I run the updater again with the next step. Originally Posted by kunix
-
3rd June 2014, 10:42 PM #25Navigation software Moderator
- Join Date
- Sep 2011
- Location
- Belarus
- Posts
- 908
- Rep Power
- 439
I think you can restart updater.exe after flashing each RGN.
-
3rd June 2014, 10:45 PM #26Member
- Join Date
- May 2014
- Location
- US
- Age
- 60
- Posts
- 19
- Rep Power
- 0
I'm not afraid, RGN Tool just doesn't do what I thought it would do.
If I just uncheck the boot.bin checkbox, it says "Section 1 must be enabled. Normally it should contain section '0800' boot.bin." So I *have* to move the fw_all.bin segment.
-
3rd June 2014, 11:15 PM #27Member
- Join Date
- May 2014
- Location
- US
- Age
- 60
- Posts
- 19
- Rep Power
- 0
Latest update:
1) I flashed with boot.bin only fw. "Update successful" - Cannot flash again with restarting to pre-boot mode.
2) Flashed with fw_all.bin only fw "Update successful" - I can immediately flash boot.bin without restarting.
3) Flashed with boot.bin fw "Update successful" - Cannot flash again with restarting to pre-boot mode.
4) Restarted - it's back to "Loading maps..." hang. Woohoo.
5) Flashed with 0827 cure firmware - IOU_UTILITIES error
6) Restarted - "Loading maps..." hang
It doesn't show up in RMPrepUSB tool during any of these steps however.
I've repeated the above steps several times, and I'm at step 3 now.
What's next?
-
4th June 2014, 01:15 AM #28Garmin/GPS Systems GMod.
- Join Date
- Aug 2011
- Location
- Oz.
- Posts
- 6,115
- Rep Power
- 1616
'Thanking Posts' are banned. To thank someone, and/or to see hidden links and content, use the [Only registered and activated users can see links. ] button below left of the helpful post then refresh your browser [F5 key]. 'Thanking Posts' are banned.
Please don't spam. Posts serving no purpose other than to thank or to ask about hidden links are trashed or deleted, it's GPSPower's policy. Please don't spam.
[Only registered and activated users can see links. ] should make their first post as a new Intro Thread in [Only registered and activated users can see links. ].
-
4th June 2014, 07:17 AM #29Navigation software Moderator
- Join Date
- Sep 2011
- Location
- Belarus
- Posts
- 908
- Rep Power
- 439
pgardella, can you confirm that flashing RGN with original fw_all.bin only completes successfully, but flashing RGN with the same fw_all.bin, but patched by GarminCure3's CURE option, completes with IOU_UTILITIES error?
Neil , I think we can do this already. But there could be a bigger problem...
-
4th June 2014, 12:29 PM #30Member
- Join Date
- May 2014
- Location
- US
- Age
- 60
- Posts
- 19
- Rep Power
- 0
I can flash with boot.bin-only RGN successfully. I can flash with fw_all.bin-only RGN successfully. But if I flash with the original (boot.bin & fw_all.bin) run through CURE fails with the IOU_UTILITIES error. I have not tried flashing with fw_all.bin run through CURE. I don't know enough about the firmware to know if this would work or break something worse. Originally Posted by kunix
Last edited by pgardella; 4th June 2014 at 12:32 PM.
Bookmarks