No problem![]()
Hi for all,
is there amy problem with GTM36 and 3490 (2014 SW) if I mod region 140 to enable MP3 player?
Thank you!
Hello everybody!
After "unsuccessful" input of one of subscription codes, the traffic receiver (gtm 36) has ceased to work.
...dead link ...
It can be cured somehow?
Thank you.
What GPS model are you using?
What traffic signature was installed and what new one did you try to install?
Please put the other screens of the traffic menu, especially the traffic signature.
DriveLuxe50, Nuvi 2689, Etrex 30x, Epix, VivoActive HR.
Nuvi 2495 lt/gtm 36. I tried to install signature for here traffic (ru) with the following data: FID: 18183, PID: 1, RID: 0 , VID: 0. Of course nothing was added, but stop tuning.
...
Last edited by ivagvoz; 8th September 2017 at 08:14 AM.
I see some problems: first, the GTM 26 and 26 cables are not compatible with non-original parallel signatures generated by the JetMouse in the 2012 series gps (24x5, 25x5, 3400, 3500). So all signatures installed with jetmouse do not work on these gps, including yours, see the posts on page 3 and after on this topic. However, other original factory-installed signatures work normally. On the other hand, the Jetmouse signature on the same cable, should work with earlier models of gps and some later.
The error that your screen displays seems to have no direct relation to the subscription, but with some update of the firmware of the cable / tuner, I have seen this happen. The updates are automatic and it is very likely that you have not noticed .. But we will see possible solutions later.
Another problem is in relation to the parameters of the signature that you showed: where you got it, are you sure that it is tested and it works? Did you install any other before it? The one that you have has VID = 0 which indicates a signature to delete another one already installed, that is, to delete the signature 18183, 1, 0, 1
You have missed the GTM Info screen, where the FM stations and the tuning codes appear ..
DriveLuxe50, Nuvi 2689, Etrex 30x, Epix, VivoActive HR.
Hi guys, I have read everything I could find on this forum but I haven't found an answer to my problem.
So I'm writing in this old thread and I hope someone can help me.
I got a GTM35 on my desk with the following problem during Traffic provider finds providers but TMC does not work.
9/e4/2/35 4 3 is the code but it does not show the traffic information, I have connected the receiver to 2 different NUVI's and the problem persists.
But when I connect the GTM36, the receiver accepts the 9/e4/2/35 0 4 information and displays it correctly.
on both GTM35/36 receivers the lifetime subscription to Radio SI/TrafficNav (SI) is also activated.
Last edited by Boki; 1st May 2025 at 10:17 PM. Reason: approved
Which 2 nuvi devices are you testing the GTM35 and 36 with? However, it's unlikely to be a compatibility issue as usually it's the other way around, i.e. older devices might not recognize the newer 36 but work fine with the 35.
'Thanking Posts' are banned. To thank someone, and/or to see hidden links and content, use the [Only registered and activated users can see links. ] button below left of the helpful post then refresh your browser [F5 key]. 'Thanking Posts' are banned.
Please don't spam. Posts serving no purpose other than to thank or to ask about hidden links are trashed or deleted, it's GPSPower's policy. Please don't spam.
[Only registered and activated users can see links. ] should make their first post as a new Intro Thread in [Only registered and activated users can see links. ].
Thank you for your response one is nuvi 3490 the other is nuvi 2350.
If I set the frequency in FM Traffic status , it starts receiving information but when I put it back to NORM it stops. But even though it receives the information it doesn't display it .Maybe there is a problem in TrafficProvider.xml, currently I have replaced 4.90 with 4.80.
But both nuvi-s with GTM36 are working without problems.
Bookmarks