City Navigator Europe NT 2011.30

**pallexl** · 21st November 2010, 10:40 PM

Originally Posted by MikieP

pallexl-

From what I understand about the the 3790 as well as my 885T, the .SRD files stay as is and only the .ASR and .SRX files need updating to coincide with the new map(s). If you get errors doing a Find Address using Voice Commands you have something wrong, even though most or all other Voice Command functions may still continue to work properly.

MikieP

ok, thanks. I have loaded 2011.30 to MapSource, made my selection of maps, transfered to my device, renamed and unlocked the new image and then reloaded into the .system folder. In addition to this step I have replaced asr+srx files and 3D image and all other relevant files found in the 2011.30 install package - now map functions works fine, but for some strange reason some of the voice commands don't...I'm getting technical fustrated - any help is appiciated :-)

**MikieP** · 21st November 2010, 11:41 PM

Originally Posted by pallexl

ok, thanks. I have loaded 2011.30 to MapSource, made my selection of maps, transfered to my device, renamed and unlocked the new image and then reloaded into the .system folder. In addition to this step I have replaced asr+srx files and 3D image and all other relevant files found in the 2011.30 install package - now map functions works fine, but for some strange reason some of the voice commands don't...I'm getting technical fustrated - any help is appiciated :-)

Well, the ASR files in post 1 may be for the 885T or the 3790, I can not tell and no one has indicated which unit as well. The size, 727mb, does not tell me as I do not know which size goes to which unit. If they are for 885T, they will not work in the 3790 as far as I know and the reverse seems to be true as well. We need someone with knowledge in this area. For certain, if you have voice command errors, one set of files is wrong or they are not installed in the correct place. I think you installed the gmapprom by downloading the mapsource files? Not sure that will work with your voice commands, it would not for my 885T. I had to install the entire locked image (this was for NA CNNT 2011.20 since .30 ASR files do not seem to be around as yet so I can not test this newer update) file complete for NA CNNT, unlock it using a key and then and then only would my voice commands work for Find address. Do not know if this is applies to the 3790 but would assume it does.

MikieP

**pallexl** · 22nd November 2010, 12:02 AM

Originally Posted by MikieP

Well, the ASR files in post 1 may be for the 885T or the 3790, I can not tell and no one has indicated which unit as well. The size, 727mb, does not tell me as I do not know which size goes to which unit. If they are for 885T, they will not work in the 3790 as far as I know and the reverse seems to be true as well. We need someone with knowledge in this area. For certain, if you have voice command errors, one set of files is wrong or they are not installed in the correct place. I think you installed the gmapprom by downloading the mapsource files? Not sure that will work with your voice commands, it would not for my 885T. I had to install the entire locked image (this was for NA CNNT 2011.20 since .30 ASR files do not seem to be around as yet so I can not test this newer update) file complete for NA CNNT, unlock it using a key and then and then only would my voice commands work for Find address. Do not know if this is applies to the 3790 but would assume it does.

MikieP

Thanks Mikie - your help is appriciated. Can I ask one more thing? How do you make this step "I had to install the entire locked image (this was for NA CNNT 2011.20 since .30 ASR files do not seem to be around as yet so I can not test this newer update) file complete for NA CNNT, unlock it using a key"?

**MikieP** · 22nd November 2010, 12:26 AM

Originally Posted by pallexl

Thanks Mikie - your help is appriciated. Can I ask one more thing? How do you make this step "I had to install the entire locked image (this was for NA CNNT 2011.20 since .30 ASR files do not seem to be around as yet so I can not test this newer update) file complete for NA CNNT, unlock it using a key"?

I think what you are asking is the step by step for getting the entire locked image in Post 1 into your GPS? D/l the image. uncompress it. rename it to gmapprom.img if different. Hook up the gps using a usb cable. using Explorer or some other File Manager to get to the 8xx gps \garmin sub dir or 37xx .system directory. Copy the gmapprom.img on your GPS to somewhere on your computer hard drive so you have a back up copy of it. Once copied, then copy the new gmapprom.img you uncompressed back to the 8xx GPS \garmin directory or 37xx .system directory. It will ask to overwrite. Tell it yes. Once the file is copied to your gps, use a text editor like notepad to create "gmapprom.unl", an empty file on your PC. Then, using jm keygen v1.5, enter your GPS Serial Number in the top block, press Generate block midway down, then drop down to next block where it asks for what map, go to bottom map name drop down block, and hit "other", a block pops up and then you enter 2281 into this block (this mapset ID), hit enter, press generate block near bottom, copy and paste the serial number from the very bottom block into the gmapprom.unl file on your PC Copy this file to the same place you sent the new gmapprom.img file on your GPS. Done. Disconnect GPS safely. Map should now be unlocked and function OK when you turn GPS on. If all is well, map comes up meaning it is successfully unlocked, then try using voice command to Find Address. If GPS says locked map when starting up, then redo the key gen steps.. you entered incorrect serial or map id... If Find Address gives an error, then there are errors to look at like incorrect ASR files, and other things that seem to go wrong with these voice units.

MikieP

**brocot** · 22nd November 2010, 10:40 AM

Originally Posted by MikieP

I think what you are asking is the step by step for getting the entire locked image in Post 1 into your GPS? D/l the image. uncompress it. rename it to gmapprom.img if different. Hook up the gps using a usb cable. using Explorer or some other File Manager to get to the 8xx gps \garmin sub dir or 37xx .system directory. Copy the gmapprom.img on your GPS to somewhere on your computer hard drive so you have a back up copy of it. Once copied, then copy the new gmapprom.img you uncompressed back to the 8xx GPS \garmin directory or 37xx .system directory. It will ask to overwrite. Tell it yes. Once the file is copied to your gps, use a text editor like notepad to create "gmapprom.unl", an empty file on your PC. Then, using jm keygen v1.5, enter your GPS Serial Number in the top block, press Generate block midway down, then drop down to next block where it asks for what map, go to bottom map name drop down block, and hit "other", a block pops up and then you enter 2281 into this block (this mapset ID), hit enter, press generate block near bottom, copy and paste the serial number from the very bottom block into the gmapprom.unl file on your PC Copy this file to the same place you sent the new gmapprom.img file on your GPS. Done. Disconnect GPS safely. Map should now be unlocked and function OK when you turn GPS on. If all is well, map comes up meaning it is successfully unlocked, then try using voice command to Find Address. If GPS says locked map when starting up, then redo the key gen steps.. you entered incorrect serial or map id... If Find Address gives an error, then there are errors to look at like incorrect ASR files, and other things that seem to go wrong with these voice units.

MikieP

Hi,
GPS says locked map when starting up. But the map is working and loaded . In the screen Info from the Map i have "City Navigator Europe NT 2011.30"
I have it installed as "gmapprom.img". I have the updated Unl file. Do i have to claen up the previous serial number in the Unl file ?
How do i get rid of that "locked map when starting up "

**MikieP** · 22nd November 2010, 10:53 AM

Originally Posted by brocot

Hi,
GPS says locked map when starting up. But the map is working and loaded . In the screen Info from the Map i have "City Navigator Europe NT 2011.30"
I have it installed as "gmapprom.img". I have the updated Unl file. Do i have to claen up the previous serial number in the Unl file ?
How do i get rid of that "locked map when starting up "

Sounds like you did the keygen stuff wrong. put gps serial number in top block, press generate beneath it. Then below that Select Map product, use other, then enter 2281 in empty block press generate below that and paste 25 digit serial into the gmapprom.unl in the GPS. Both gmapprom.img and gmapprom.unl should be in the \garmin (older nuvi)or \garmin\.system directory (37xx) That is all that should be in the file. just the 25 digits you just generated - delete any other data in the file. it must have the same name as the gmapprom.img file except the the suffix is unl instead of img. That should fix your locked map problem.

**brocot** · 22nd November 2010, 08:41 PM

What is the file "gmapprom.sum" "gmap3d.sum"
can they stay as the are after changing the "gmap3d.img" gmapprom.img ?

**pallexl** · 22nd November 2010, 06:36 PM

Originally Posted by MikieP

I think what you are asking is the step by step for getting the entire locked image in Post 1 into your GPS? D/l the image. uncompress it. rename it to gmapprom.img if different. Hook up the gps using a usb cable. using Explorer or some other File Manager to get to the 8xx gps \garmin sub dir or 37xx .system directory. Copy the gmapprom.img on your GPS to somewhere on your computer hard drive so you have a back up copy of it. Once copied, then copy the new gmapprom.img you uncompressed back to the 8xx GPS \garmin directory or 37xx .system directory. It will ask to overwrite. Tell it yes. Once the file is copied to your gps, use a text editor like notepad to create "gmapprom.unl", an empty file on your PC. Then, using jm keygen v1.5, enter your GPS Serial Number in the top block, press Generate block midway down, then drop down to next block where it asks for what map, go to bottom map name drop down block, and hit "other", a block pops up and then you enter 2281 into this block (this mapset ID), hit enter, press generate block near bottom, copy and paste the serial number from the very bottom block into the gmapprom.unl file on your PC Copy this file to the same place you sent the new gmapprom.img file on your GPS. Done. Disconnect GPS safely. Map should now be unlocked and function OK when you turn GPS on. If all is well, map comes up meaning it is successfully unlocked, then try using voice command to Find Address. If GPS says locked map when starting up, then redo the key gen steps.. you entered incorrect serial or map id... If Find Address gives an error, then there are errors to look at like incorrect ASR files, and other things that seem to go wrong with these voice units.

MikieP

Thanks again Mikie - can I ask what locked image you are referring to i post #1? I have the complete download, but fail to find an locked image file....if I understand you correct, theres no need for mapsource in this process?

**vincent856** · 22nd November 2010, 07:08 PM

if you need a map--there are procedures here to assist you--

if you want a step by step procedure--that will allow you to install a map without understanding, what you are doing-
you will be unsuccessful---

learn the map install process and you can install maps for the rest of your life--

i assure you its hard to learn-but once you understand the process--its quite simple--

**pallexl** · 22nd November 2010, 07:16 PM

Originally Posted by vincent856

if you need a map--there are procedures here to assist you--

if you want a step by step procedure--that will allow you to install a map without understanding, what you are doing-
you will be unsuccessful---

learn the map install process and you can install maps for the rest of your life--

i assure you its hard to learn-but once you understand the process--its quite simple--

well well, what a nice comment - are you here to help and exchange knowledge or play smart?

Thread: City Navigator Europe NT 2011.30

Thread Tools

Display

Hybrid View

Advertissements

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions