kenwood dnx9260bt mass storage deleted

**Toretto** · 23rd June 2015, 09:26 AM

First at all:

You can find on the internet the Kenwood service manual. The problem is that there is no navigation part on the scheme. It is presented only as a module.

The missing parts are probably resistors. I have this parts in my board too, the same like ORAK. When I'll go back to home I'll check it out on my navi board. Most probably the navi board are the same. The difference is in the software.

The second thing - you soldered black and red wires to the navi board.
On the pictures You showing us any black and yellow wires are connected near any harness. Could You explain what You exactly doing? Maybe show any photo whole unit with cables. Especially cables from navi.

EDIT

OK, ORAK has the values of resistors, but for sure I give in this place:

First, smaller - 1k
Second, bigger - 10k

**ORAK** · 23rd June 2015, 08:44 PM

Now you have the values of resistance.
I will give council, Go to a real electronics to solder the 2 resistances and thinner wires.
To not spoil anything else, You didn't do real soldering.

**mylona79** · 24th June 2015, 07:30 AM

i connected the radio to a ups power supply. in oprder to power up the radio i have to connect the red and yellow wires together and black to ground. but now i only have the gps module connected to the usb not thje radioi . and i aldo have the red and black wire connected together. i took the board to an electronics technician and he told me that the 2 resistors that are missing dont matter because he check where they go on the opposite side of the pcb board and they dont connect to anywhere. i am goiny to take it again to make a proper soldering

**ORAK** · 24th June 2015, 09:24 AM

Please change the electronics technician, he knows what makes?
Watch here:

Spoiler: pics

This is not the double-layer board.
This it is a multilayer board.
Please search on Internet the difference between double-layer board and multilayer board.

Spoiler: pic

P.S.
For me ..... Game Over.

**Toretto** · 24th June 2015, 11:21 AM

Electronic equipment has always what has to have on board.
Nobody gives no needed components.
In this case possible/probably - it's ADC reading for processor from resistance divider...
As Orak wrote - change technician...

**mylona79** · 7th July 2015, 12:04 PM

i finally fixed it.but i amfacing other problem my navigation screen only is showing in pink color do you know why ?

**ORAK** · 7th July 2015, 08:12 PM

In the end I was right.
Only in the navigator is showing in pink color ?
ReCheck all Ribbon Flat Cable to which walked / removed, attacking systems for Ribbon Flat Cable
I think that you don't have attaching, removable front panel monitor in the right way.
The same thing It happened to me.
Try an detaching and attaching for removable front panel monitor in the right way.
You go here and see this movie: Kenwood Instruction Detachable Screen

Spoiler: YT video

**mylona79** · 8th July 2015, 10:52 AM

Orak once again you are very correct i did what you said me and the color is fixed back to normal.

i am facing onother problem. the up and down arrows dont adjust the monitor . the ancle . do you know why ?

**ORAK** · 8th July 2015, 05:10 PM

Up and down arrows only adjusts the volume you can see on page 12 of Instruction_Manual_English.pdf
For adjusts the monitor you can see on page 73 of chapter Monitor Angle Control from Instruction_Manual_English.pdf
Here is all the manuals about DNX9260BT:
- GPS Navigation Instruction_Manual
- Instalation Manual
- Instruction_Manual_English
- SERVICE MANUAL
- Voice Command 1
- Voice Command 2

[Only registered and activated users can see links. ]

Another secret.
When you drive at night, light from the monitor is too strong.
You can turn off the monitor, touch button "AUD" more than 2 seconds.

Monitor will turn off, but everything is perfectly functional.

Spoiler: pic2

To activate the monitor, touch screen at any point.

**mylona79** · 12th July 2015, 08:43 PM

i am facing another problem.i fix the navigation and everything. everything works ok except that the maps cannot be seen. i see the arrow and everything but not the maps. and also webupdater recognize my device but fails at the end saying that the device could noty communicate with the laptop i will show fotos

removed dead pics

Thread: kenwood dnx9260bt mass storage deleted

Thread Tools

Display

Advertissements

Bookmarks

Bookmarks

Posting Permissions