Thread: how to zoom in in primo 9.6.29.483387

Originally Posted by I7210I

here is better [Only registered and activated users can see links. ] can you see the different?
here it's older but still closer [Only registered and activated users can see links. ]
...is there option to see the navigation like these at the junctions...

These are two different programs. Igo 8.x and Primo, for WinCE and low resolutions. Their show is a little bit different.
It is obvious that we did not quite understand. You want an even greater zoom then factory declared? Or I am wrong?
Explain to me your first sentence to be clear : "...I suddenly saw that the zoom in option that was till now is missing...". Is this mean that zoom was OK at same device with same program and than changed? Or you have used Igo/Primo on old device and now you try it on new?

Solutions?...Hmmm...try without skins, try with other skin... try with clean version of Primo or with some pack that proven works well.
For navigation look like on juctions: that is hardware problem, in fact, in order to show such a realistic picture, we would have to have a lot more stronger devices to display it. But, as you know, programs like this must works at any hardware (old/new, week/strong).

Originally Posted by wojpen

...explore the issue, Look at the screen's:...
You see the difference?
And believe me - it has nothing to do with what you wrote... zoom 2d

Yeah dear colleague. I see. But you didn't show nothing useful.
For the 2d zom, I get it, after next pictures of I7210I. Oposite solution. As I said to the user, obviously setting the problem is different then it looks.

Originally Posted by Boki_Srb

Yeah dear colleague. I see. But you didn't show nothing useful.
For the 2d zom, I get it, after next pictures of I7210I. Oposite solution. As I said to the user, obviously setting the problem is different then it looks.

Hi,
Welcome,
I.
If the attached screen's do not see anything interesting - it's either I'm blind, or you look carelessly.
Look at the size of the viewing area - and thus the width of roads etc. - See the difference?
And repeat once again - is never a matter of what you offer! in your first post.
II.
Whether we are talking about iGO - for Android, WinMob, or WinCe - how to implement display of the map is the same. It is the responsibility records in those places - which I wrote.

I suggest that you have done to try to experience:

You have file sys.txt
In it is the section

[debug]
write at the end of such a declaration:

fov=45
just run and see on the screen.
then change your declaration on

fov=30 and look screen
then
fov=70 and look.
You see the difference?

III.
Browsing the map:
[Only registered and activated users can see links. ]


FOR:
ANGLE =0 => cam above car
ANGLE =90 => cam behind car on the ground
ANGLE CALCULATION TWO METHODS USED:

1) NOT AT MANEUVER/NO ROUTE -> ACTUAL SPEED (MIN/MAXSPEED) IS ANGLE (MAX/MINANGLE)
2) WITHIN MAXDISTANCE FROM MANEUVER -> ACTUAL DISTANCE TO MANEUVER IS ANGLE (MAX/MINANGLE-OFFSET)

IV.
In iGO which has installed skin - eg. Doupas, Dimka, GjAK - such as zoom, angle can be changed in the program.
Look this screen's: (eg. Skin Doupas_8.4)
[Only registered and activated users can see links. ],[Only registered and activated users can see links. ],[Only registered and activated users can see links. ],[Only registered and activated users can see links. ]

and whitout any skin:
[Only registered and activated users can see links. ]
...............................................
As you can see on the screen - in iGO picture settings are implemented for two main parameters:
1) View Mode (2D or 3D)
2) Viewpoint (Normal, High, or Low) - the height at which it is [camera]

That is:
for default (whitout skin) - only !!! View Mode and Viewpoint,
for skin's-mode - many, many other additional parameters.

You can change this so that the default mode - also existed the possibility to declare additional parameters ...
but more on that in the next post!
regards wojpen
I'm going to the beach - is weirdly hot