Visibility of town and village names on map

[linknet]

I have a problem when searching the map for towns and villages since their names only appear on the map at one very specific value of map zoom. If I zoom in or zoom out from this value, even very slightly, then the names disappear.

Are there any sys.txt settings which will change this behaviour?

Spoiler: Names visible at one specific zoom level only

[Only registered and activated users can see links. ]

Spoiler: Names disappear after very slightly zooming in or out

[Only registered and activated users can see links. ]

[linknet]

I found the answer, I needed to edit the data.zip\ui_nextgen\common\default.vis file:

Spoiler: Edited default.vis file:

[Label200m-6500m] ( original value [Label600m-4300m] )
area=0,1,2
poi="Settlement.class1", "defaultbd", "label_settlements", 14,"settlements",1
+++++++++++++++++++++++++++++++++++++++++++++++
poi="Settlement.class11", "default", "label_settlements", 10,"settlements",3

[Label6500m-13km] ( original value [Label4300m-13km] )
area=6,7,2
poi="Settlement.class1", "defaultbd", "label_settlements", 14,"settlements",1
+++++++++++++++++++++++++++++++++++++++++++++++
poi="Settlement.class10", "defaultbd", "label_settlements", 10,"settlements",3

[Label13km-25km]
area=6,7
poi="Settlement.class0", "defaultbd", "label_settlements", 16,"settlements",1
+++++++++++++++++++++++++++++++++++++++++++++++
poi="Settlement.class9", "defaultbd", "label_settlements", 10,"settlements",3

[Label25km-45km]
area=6,7
poi="Settlement.class0", "defaultbd", "label_settlements", 16,"settlements",1
+++++++++++++++++++++++++++++++++++++++++++++++
poi="Settlement.class8", "defaultbd", "label_settlements", 10,"settlements",3

[Label45km-120km]
area=6,7
poi="Settlement.class0", "defaultbd", "label_settlements", 16,"settlements",1
+++++++++++++++++++++++++++++++++++++++++++++++
poi="Settlement.class7", "defaultbd", "label_settlements", 10,"settlements",3

[Label120km-170km]
area=6,7
poi="Settlement.class0", "defaultbd", "label_settlements", 16,"settlements",1
+++++++++++++++++++++++++++++++++++++++++++++++
poi="Settlement.class6", "defaultbd", "label_settlements", 10,"settlements",3

[Label170km-300km]
area=6,7
poi="Settlement.class0", "defaultbd", "label_settlements", 16,"settlements",1
+++++++++++++++++++++++++++++++++++++++++++++++
poi="Settlement.class4", "defaultbd", "label_settlements", 11,"settlements",3

[Label300km-410km]
area=6,7
poi="Settlement.class0", "defaultbd", "label_settlements", 16,"settlements",1
+++++++++++++++++++++++++++++++++++++++++++++++
poi="Settlement.class3", "defaultbd", "label_settlements", 12,"settlements",2

[Label410km-800km]
area=6
poi="Settlement.class0", "defaultbd", "label_settlements", 16,"settlements",1
+++++++++++++++++++++++++++++++++++++++++++++++
poi="Settlement.class2", "defaultbd", "label_settlements", 13,"settlements",2

[Dorakeks]

I'm on the way at the moment and the same thing makes me angry. I did the editing mentioned here and everything is fine. Thank you so much. I found a file with the same name in "config" and edited it the same way. Editing "data.zip" from Android device was only possible with Total Commander.

Изпратено от моят Redmi 4X с помощта на Tapatalk