Hi
Does any body have a logo bin file for Nulink 1695, or any where I may find it .....(or a boot.bin
Thanks
Hi
Does any body have a logo bin file for Nulink 1695, or any where I may find it .....(or a boot.bin
Thanks
Last edited by mallard2; 3rd October 2013 at 08:09 PM.
My nuvi is 1310. How I install 13xx logo in it?
Step 1: Create the .RGN file to replace the logo in GPS:
Step 1: Get your nuvi firmware and with RGN tool extract the boot.bin
[Only registered and activated users can see links. ]
Then
1- Restart RGN_Tool.
2- Enable the first firmware region checkbox on the left.
3- Click the Load button in that region on the right. Select the boot.bin file corresponding to the firmware in your GPS. It is important that the HWID of your boot.bin matches the one on your GPS. Click Open.
4- Enable the second firmware region checkbox on the left.
5- Click the Load button in that region on the right. Select the new logo file Click Open.
6- Save it the whole thing as something like "logo nuvixxx hwid xxxx.rgn"
Step 2: Flash the GPS with the new logo
1- Drag the new logo over Updater.exe from Garmin
[Only registered and activated users can see links. ]
2- Select "USB Device" in the "Connection Settings"
3- Put your GPS in service/pre-boot mode.
[Only registered and activated users can see links. ]
4- Once the GPS is detected, click OK in updater.exe to start the programming (maintain finger on screen)
5- Once the programming is finished, click OK in updater.exe.
6- Remove USB cable.
7- Notice the GPS does not reboot by itself. No worry. The GPS is expecting more firmware that will never come. Simply turn off GPS by clicking and maintaining the GPS power button for 10 seconds until it shuts down.
8- Power-up the GPS and you have the new logo.
Infos adapted here from this turboccc thread
[Only registered and activated users can see links. ]
NOTE: before doing this please backup nuvi NV:
[Only registered and activated users can see links. ]
Last edited by catymag; 5th July 2014 at 01:32 AM.
You have to navigate to get to the good.
Galaxy S5 Kitkat 4.4.2 / Nuvi1200->1250 / Nuvi3790T->34xx / Nuvi 2200 / Nuvi 66 / Oregon 600
Here is logo for nuvi 2x5, 2x5 MTK, 2x5W and 2x5W MTK.
Its for all this nuvi in one pack.
Spoiler:
Download and extract rar on empty SD
Add SD in nuvi and turn on nuvi and whait for nuvi to restart automaticly.
When nuvi turn on, you will have enabled TTS.
p.s.
In folder Garmin/Backup on your SD you have backup of your original logo, so add this on save place on Pc.
Now you can erase folder Garmin from SD.
Last edited by Neil; 23rd August 2015 at 10:31 PM.
How to see the logo?
You have to navigate to get to the good.
Galaxy S5 Kitkat 4.4.2 / Nuvi1200->1250 / Nuvi3790T->34xx / Nuvi 2200 / Nuvi 66 / Oregon 600
I think i lost BMW logo, because it seems to me it was in area 16 & i did not backup that area (because i did't know) before converting to 34xx........................
I'll try to get that image from NÜVI 715 BMW Edition or from Nüvi 860 BMW edition, but i dont know in what area is this located on these units.
We will see whats going to happen.................
On all nuvi logo is in region 16.
We have somewere on Noeman BMW logo from nuvi 3760.
I found the posting, but link to download BMW logo for 37xx is dead.
Also, i just found out that, after converting BMW 3760 to 34xx i propably lost (don't have cradle from BMW yet, was planning to buy one, have part# for it) audio output to radio.
I have two original cradles from BMW for 8xx series & 7xx Series Nüvis.
8xx series cradle works fine to output Stereo audio to Radio on all 8xx NÜVIs, BMW Version or not ( I'm using original GARMIN, NON BMW 865 NUVI now, on my Mercedes COMAND with BMW Cradle).
7xx series cradle also works but, audio is only comming out on specific 7xx BMW version NÜVIs. Regular 7xx serie NÜVIs does't output any audio, over BMW cradle at all & it is same with Mercedes cradle as well.
Last edited by Kaluluka; 14th January 2013 at 02:07 PM.
If this is the case that all nuvi logos are in region 16, is it safer to use Updater via microSD card as below?
To read/extract current logo (content of update.txt):
rrgn,16,1:/16.bin
reboot
Rename the downloaded logo to 16.bin then load as follows(content of update.txt):
xrgn,16,1:/16.bin
reboot
Bookmarks