Adriaroute work perfect, broblem was only in FW 5.20.
If you have problem in 6.10 and 6.20, then do hard reset, but don't forget to create backup of folder GPX.
I coudn't understand well the issue but better contact Garmin HR. Could be map settings.
Adriaroute work perfect, broblem was only in FW 5.20.
If you have problem in 6.10 and 6.20, then do hard reset, but don't forget to create backup of folder GPX.
I have unchecked all other maps. There was problem on whole map. The problem started when i updated firmware to 6.10. In 3D view of the map (like when driving), map do not show all the roads. The same when i look in "browse map". When i zoom in few times in both these views, then i can see all roads right. When i zoom out, parts of the roads dissappear. All the time, most map view checked in settings. And only one map selected. In 5.90 version of firmware, everything works all right. I tried 6.20, the same thing like 6.10.
In ver. 5.x, i don't remember, there was a problem, but that time colors of third party maps was strange, black, purple, fluo green. That was fixed in one of the following updates.
Thanks to all.
I will try hard reset.
I did hard reset, and everything is the same. I can see all the roads only when i zoom in. In standard 3d view when driving, only some segments of the roads (that should be seen in most map detail) are visible. Then i installed back 5.90. When i set map detail to normal i only see main roads (yellow or orange), when i set most map detail, then i can see small roads (gray). On 6.1/6.20 only some parts of small (gray) roads can be seen, when i touch the map on the main screen. When i zoom in, then i can see all the roads like on 5.90, but not in normal view distance. I'm sure the problem is in firmware.
Last edited by vunavuna; 4th March 2013 at 12:19 AM.
Garmin, how much is 30 pieces of silver for Judas today? Were they worthy for crucifix of GPSPower?
I tried that. I inastlled only one map on sd card. Adria route in this case. And the problem persisted. Similar thing is happening when i change map detail in mapsource, on lower settings. I don't know is there a difference when transfering map by mapsource or mapinstall or basecamp, i only use mapsource.
edit: Just tried to transfer map with the newest version of mapinstall (4.0.3) and mapsource (6.16.3), and all the same. I thougt maybe the problem is in older version of mapsource, but it is not. I dont know what it coud be if not firmare problem?
Here is what is like:
Adria route_____________________________CNEU
[Only registered and activated users can see links. ][Only registered and activated users can see links. ]
Adria route_____________________________CNEU
[Only registered and activated users can see links. ][Only registered and activated users can see links. ]
Last edited by vunavuna; 4th March 2013 at 07:56 AM.
Garmin, how much is 30 pieces of silver for Judas today? Were they worthy for crucifix of GPSPower?
Download unlocked AR 4.10 and add in your nuvi and AR will work like charm
When you set CN and then back AR, do you turn off nuvi and then On?
If you have enabled CN and you like to run AR, you must first untick CN, Tick AR and then turn off and on again your nuvi.
I tried everything. Turning off/on, hard reset, soft reset... Of course i have unchecked CNEU when i checked AR. I even transfered only AR to sd card, and same thing again. I think the problem is that newer firmwares are not in good relationship with some third party maps.
I'll wait for new firmware or newer map. For now, 5.90 work like a charm with every map i have.
Last edited by vunavuna; 5th March 2013 at 02:09 AM.
Bookmarks