Welcome guest, is this your first visit? Click the "Create Account" button now to join.
Page 18 of 60 FirstFirst ... 8161718192028 ... LastLast
Results 171 to 180 of 592

Thread: Firmwares Smeg+

  1. #171
    Member
    Join Date
    Nov 2014
    Location
    PT
    Posts
    9
    Rep Power
    0

    Default

    Quote Originally Posted by billouetaudr View Post
    Hi, do you have theme choice with the 5.4 or not on your Cactus ? Thx
    I could not find any way of setting a different theme. If you find out an alternative of choosing a diferent theme, please tell me.

  2.    Advertissements


  3. #172
    Master Firmwares Smeg+Firmwares Smeg+
    Join Date
    Apr 2015
    Location
    Mumbai
    Posts
    81
    Rep Power
    59

    Rom Some pitfalls on a 508 to consider

    As an Adventurous guy, I had to try the update 5.4.B.R6 with my SMEG+ on a 2015 Peugeot 508.

    At first, the update was accepted by the unit's self test and the install began normally. Then, at the APPBIN phase, the update hung, i.e. progess on the infamous blue screen went on and on and on...

    [Only registered and activated users can see links. ]

    So, after getting tired of waiting, I switched off the engine and disconnected the battery. After half a minute, I reconnected it with the USB key still connected. The update then continued with a blank
    (read: black) screen! 10 minutes later, the unit rebooted with two splash screens: first the Peugeot lion and then the Citroen wave! That was one hell of a laugh!
    After the unit had completed booting, it showed a light theme belonging to a Citroen Cactus or something! Very funny theme, btw. I changed the display theme to Square Blue and all was back to normal again...
    Also, the Citroen wave was gone on the next boot.

    All the settings and POIs were retained throughout the update.

    All in all, the update succeeded. The SMEG+ is functioning normal again, running the 5.4.B.R6 software.

    So, if you try 5.4.B.R6 bear in mind that there some pitfalls! Also, this update takes considerably longer than a "normal" one.

    Greetz,
    Wayne

    P.S: Has anyone ever tried to revert back to an earlier version of the firmware? Is this possible?
    Last edited by WayneLaPie; 30th December 2015 at 02:30 PM.

  4. #173
    Junior Member
    Join Date
    Oct 2015
    Location
    Denmark
    Posts
    2
    Rep Power
    0

    Default

    Quote Originally Posted by WayneLaPie View Post
    As an Adventurous guy, I had to try the update 5.4.B.R6 with my SMEG+ on a 2015 Peugeot 508.

    At first, the update was accepted by the unit's self test and the install began normally. Then, at the APPINIT phase, the update hung, i.e. progess on the infamous blue screen went on and on and on...

    So, after getting tired of waiting, I switched off the engine and disconnected the battery. After half a minute, I reconnected it with the USB key still connected. The update then continued with a blank
    (read: black) screen! 10 minutes later, the unit rebooted with two splash screens: first the Peugeot lion and then the Citroen wave! That was one hell of a laugh!
    After the unit had completed booting, it showed a light theme belonging to a Citroen Cactus or something! Very funny theme, btw. I changed the display theme to Square Blue and all was back to normal again...
    Also, the Citroen wave was gone on the next boot.

    All the settings and POIs were retained throughout the update.

    All in all, the update succeeded. The SMEG+ is functioning normal again, running the 5.4.B.R6 software.

    So, if you try 5.4.B.R6 bear in mind that there some pitfalls! Also, this update takes considerably longer than a "normal" one.

    Greetz,
    Wayne

    P.S: Has anyone ever tried to revert back to an earlier version of the firmware? Is this possible?
    What's new in this software?? Carplay from Apple? Does it work with Grand C4 Picasso from 2015, that has 5.2?

  5. #174
    Master Firmwares Smeg+Firmwares Smeg+
    Join Date
    Apr 2015
    Location
    Mumbai
    Posts
    81
    Rep Power
    59

    Default

    AFAIK, Carplay must be activated with diagbox afterwards. I don't know if this software supports it, though, as I am allergic to apples, especially green ones.
    I noticed a new versions of the display software (32.00), but no new functions.

    As for the GP: I can't test that, but @pub did. Why don't you give it a shot?

    @pub: can you assist?

    Greetz,
    Wayne
    Last edited by WayneLaPie; 30th December 2015 at 02:28 PM.

  6. #175
    Trial Moderator Firmwares Smeg+
    Firmwares Smeg+
    Bricoman's Avatar
    Join Date
    Dec 2014
    Location
    Just around the corner's street
    Posts
    761
    Rep Power
    280

    Default

    Hello,

    What scares WayneLaPie, there is an updated concession, the 5.4.B.R8.
    You can buy 5.4.B.R6 and not this latest ?
    There must be a problem that a new update has arrived so quickly?
    Last edited by Bricoman; 5th January 2016 at 10:03 PM.

  7. #176
    Master Firmwares Smeg+Firmwares Smeg+
    Join Date
    Apr 2015
    Location
    Mumbai
    Posts
    81
    Rep Power
    59

    Default

    @Monarch: this site lists GP as compatible:

    [Only registered and activated users can see links. ]

    and @pub apparently also successfully applid the update.

    So, go ahead and try it!

    Greetz,
    Wayne

  8. #177
    Junior Member
    Join Date
    Oct 2015
    Location
    amsterdam
    Posts
    2
    Rep Power
    0

    Default

    I have a 508SW from october 2014 with touchscreen. Originally it came with SMEG 5.1.F.R4 (dated 21/02/14), and I upgraded before to SMEG 5.2.C.R1 (dated 01/08/15). Should I now choose for 5.4B.R6 or 6.1.D.R8?

  9. #178
    Member
    Join Date
    Feb 2015
    Location
    Brussels
    Age
    49
    Posts
    16
    Rep Power
    0

    Default

    @drivert
    6.1 is not for your model of SMEG+. It is for a different hardware (SMEG+ evo).
    If you want to update, you will have to choose 5.4.B.R6.
    Note that a new version 5.4.B.R8 has been released but is not yet available for download.

  10. #179
    Member
    Join Date
    Feb 2015
    Location
    Brussels
    Age
    49
    Posts
    16
    Rep Power
    0

    Default

    Quote Originally Posted by WayneLaPie View Post
    P.S: Has anyone ever tried to revert back to an earlier version of the firmware? Is this possible?
    No, the SMEG+ will refuse to revert to an earlier version. There is a check of the FW version by the SMEG at the beginning of the update procedure.

  11. #180
    Trial Moderator Firmwares Smeg+
    Firmwares Smeg+
    Bricoman's Avatar
    Join Date
    Dec 2014
    Location
    Just around the corner's street
    Posts
    761
    Rep Power
    280

    Default

    Quote Originally Posted by Bruno_T View Post
    @drivert
    6.1 is not for your model of SMEG+. It is for a different hardware (SMEG+ evo).
    If you want to update, you will have to choose 5.4.B.R6.
    Note that a new version 5.4.B.R8 has been released but is not yet available for download.
    Hello,

    We saw pass the FW 4 to FW 5, maybe soon FW 5 to FW 6 ?
    I don't think so, Smeg+iv2 is really different Smeg+ (hardware).

 

 
Page 18 of 60 FirstFirst ... 8161718192028 ... LastLast

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.