Mate it works with Primo 2.4 but not Primo 2.1 Thanks for that works good.'
cheers
Baz
Printable View
Mate it works with Primo 2.4 but not Primo 2.1 Thanks for that works good.'
cheers
Baz
thank you for your work. is this for 800X480?
Yes ,is OK for your res, i modified for all res Wince
hi every body i am a newbie and would like to know how to install mapchanger on my igo primo 2.0 internatinal edition thank you for your help
Hi,
this ux mapchanger is only for primo 2.4.
It doesn't work for primo 2.0
Download and unrar this attachement .you have two folders utility+ ux and copy in Primo folder. after in content you create a folders.Quote:
Originally Posted by crosswir [Only registered and activated users can see links. Click Here To Register...]
1. Put "UTILITY"+ UX folder in Primo's root
2. Open UTILITY\utility.ini and check DirContent= for example:
\SDMMC\NNG\Content or \Storage Card\Primo\content or ...)
3. Check ExeName= (iGo.exe or Primo.exe or ...)
4. In Content folder create subfolders: map (if your default are TA maps), map_nt (for NT),
map_ot (for other maps) and copy to each folder at least 1 map.
5. For change POI together with maps, set: swpoi=1 and create same folder
structure as for maps (poi, poi_nt, poi_ot)
Similarly can be configured to switching the following folders:
BUILDING (swbuilding=1, folders building_ta, building_nt, building_ot),
HISTSPEED (swhistspeed=1, folders histspeed_ta, histspeed_nt, histspeed_ot),
PHONEME (swphoneme=1, folders phoneme_ta, phoneme_nt, phoneme_ot).
6. For correct map provider determination please place to each
map folder one small file (may be empty, only the name is relevant.
Examples are in the folder '_copy_to_the_corresponding_map_folder'):
!map_ta.txt - for the TA maps
!map_nt.txt - for the Navteq maps
!map_ot.txt - for other provider's maps
In this case the skin will set the provider correctly during program
start and prevent displaying wrong provider that can be caused by possible
Mapchanger's fault.
ux-utility MapChanger 320_240, 480_272, 800_480 by sumsum .
This utility allows you to change the maps used by Primo.
[Only registered and activated users can see links. Click Here To Register...]
Spoiler: link
HowTo :
1. Unzip and copy the folders from the archive as shown in image below.
2. If folders already exists, copy content of folder into existing folder.
3. Each map folder must have at least a map.
4. Configure file utility\utility.ini, especially name card, as you see in image below.
[Only registered and activated users can see links. Click Here To Register...]
5. In the archives there is a file xxxx.lang wich you have to translate and rename acording to info from your lang file, as you see in image below.
6. Using Total Commander, copy this file into ux\MapChanger_24.zip\ux\MapChanger_24\lang .
[Only registered and activated users can see links. Click Here To Register...]
Any idea how to get MapChanger working like it supposed.
Right now I have set MapChanger up according to rules above. Everything is set up as supposed: content of .ini file, folder names, text and map files in them (two folders: map and map_nt). Everything to the letter.
Now when I start iGO up it works just fine, no problem there. Even shows correct map selection in MapChanger.
Thing go bad when I try to switch map.
* iGO does not restart (have to restart it manually; its more or less OK by me)
* It loads very long time and finally crashes
* Inspecting SD card folder names I see they are now different from previous restart (two folders: map_ta; and map_nt). So apparently iGO does not find maps any more and crashes.
How to fix it?
You need all 4 map folders, as it is in achive.
Also, you need at least a map on each folder.
Concerning automatic restart, you have to properly configure utility.ini , especially card name (Storage Card, SDMMC, ....) .
Thank you for your note. In the first time, there do not run, then, I have just change "utility.ini" for my équipment, I write \sdmmc\ and igo.exe for me and this give a good function and run normaly.The maps change is correct.