Printable View
On my Xiaomi Mi A2 (6Gb Ram, 128Gb Rom), iGO_AVICSYNC_9.18.28.730391 and iGO_PAL_9.18.27.719974 were running perfectly.
I have been updating to Android 10 for two days, and now only iGO_AVIC is working.
The iGO_PAL, does not work.
I would appreciate if anyone comes up with an idea to solve this problem.
Thanks in advance.
Read topic from beginning
I had read it already, and even made the explanet suggestions but I couldn't solve the problem for iGO_Pal.
This is not serious because iGO_Avic does work. The motivation is technical. If I find a solution, I will comment on this site.
Thanks to all of you.
Delete / move the TTS voice from the voice folder take a normal voice start once. Swap normal for TTS and have fun. Tested on Mi9 lite with Android 10.
It is mentioned in post #5 (problems with TTS).
A friend with Xiaomi MI 9 Android 10 made an installation for the first time the AVICSYNC (9.18.28.696728) changed by Arimi.
When starting the app without a GPS signal, it would open normally while it was "Looking for GPS signal ...".
Upon finding the GPS signal the app close.
Solution: removed the save folder, restarted the app, then returned with the save folder again.
Now it works without problems.
My Xiaomi A2 lite updated to Android 10. At first start of Primo Nextgen I;ve got a notification that Igo shouldnt work properly but started. After restart I did not get any notification and it just runs like before. So here till now no problems on 2 Xiaomi A2 lites.
Hi all,
I tried installing the iGO_Israel_9.6.29.636868 running in my old galaxy Not 4 Anroid 6.01 on my new galaxy A51 android 10, I got a splash display. So I was looking for an iGO running android 10. I've tested several iGO here in gpspower, no one works :beating:
Finally,I used [Only registered and activated users can see links. Click Here To Register...] to transfer the iGO app installed in the Galaxy Note 4 to the Galaxy A51... then I copy all content of Galaxy Note 4 - SD card/Android/data/com.nng.igoprimoisr_636868.javaclient/files/iGO to Galaxy A51- SD card/Android/data/com.nng.igoprimoisr_636868.javaclient/files/iGO and voila it works like a charm
:jumb:
It took me 2 days to make this app working on my new A51. If it can help other people and save time, I share this experience.
Regards
You make the same mistakes as most new/old users. Lost two days for nothing :smile: Next time install it by following recommendations from NG OP's.
Read [Only registered and activated users can see links. Click Here To Register...], for Primo.
TNX Boki _Srb for this info ;)
However, may you please can help with the already installed SmartSwitch iGO_Israel_9.6.29.636868 on a Galaxy S20 Ultra and Dalaxy A51?
In fact everything works just fine except the screen resolution comparing to my old Galaxy Note 4 (see image bellow).
Galaxy Note 4: fill all the screen, it has a display resolution of 2560x1440 and the iGO screenshot image properties has 2560x1440
Galaxy S20 Ultra: not fill all the screen, it has a display resolution of 3200x1440 and the iGO screenshot image properties has 2400x1080
Galaxy A51: not fill all the screen, it has a display resolution of 2400x1080 and the iGO screenshot image properties has 2400x1080
Moreover, the speed and camera icons are overlays.
I attached the sys.txt if can help
BTW, I'm using a Skin Dreamteam V4.9d EUR+ dt_mod__gpinpin_ftk_primo_android_tab320_2560_1340x1600_V4.9d7
Regards
[Only registered and activated users can see links. Click Here To Register...]