Without logo, press left-up corner just after you see a backlight is turning on (about 1-2 seconds after inserting USB cable back to device). The screen will be slightly brighter. its much more visible, if you turn device left side down.
Printable View
Without logo, press left-up corner just after you see a backlight is turning on (about 1-2 seconds after inserting USB cable back to device). The screen will be slightly brighter. its much more visible, if you turn device left side down.
to get logo ,use the file posted at the bottom of my starting post -
Unpack the file to an empty SD card, turn nuvi off, insert card, turn nuvi on.Remove sd
convert37x34.zip (911 KB)
[Only registered and activated users can see links. Click Here To Register...]
Then flash 37xx firmware
37xx firmware .rgn
nuvi37xx_GCDFile__450.rgn (48,4 MB)
[Only registered and activated users can see links. Click Here To Register...]
then rerun convert37x34 in sd like before,to get all the 37xx features and 37xx logo again
remember to clear non vol before and after every flashing and in 34xx to enable in MTP settings ,storage mode
I have lost the icon to add shorcuts in the where to screen. Is there any way to restore it? I have tried clearing the nonvol and reseting the nuvi.
Thank you everyone who replied, much appreciated. I have learnt the folly of my ways. Garmin will not let pre-boot mode load (at least on my unit) if I try to do it within 2 minutes of the previous attempt. I just waited a lot longer than 2 minutes and managed to get pre-boot mode to load every time by touching the top left corner of the screen.
I have another question and maybe this belongs in another thread.
The 3490LMT does NOT come with eco-route, if I was to get the 3490LMT (just for the faster processor - because 3d terrain rendering is sluggish on the 3790), will I be able to copy the eco-route files from my current 3790 onto the 3490? Reason I ask is the 3490 does not have EcoRoute (unless you buy it) but when I upgraded my 3790 FW, it still showed I had ecoroute. Which means I should be able to copy some files over.
Does anyone have any clues to point me in the right direction?
@ encryption
Use the xmls to unlock the ecoroute in the first post.
Hi people,
Please, your units coverted from 3790T to 34XX are working the 3D buildings?
I'm in Brazil and and GPS is installed with with CN South America 2012.40 NT and the 3D.img is on the "map" folder.
Are there something that I have to do to fix that?
Catymag,
I'm the Rodrigo from the nimraG forum!
tks!
Hello Rodrigo, yes we see 3d buildings on 34xx, download the file in the attachment in post n1Quote:
Originally Posted by rfb [Only registered and activated users can see links. Click Here To Register...]
To get all the features availables you must copy these *.xml files in /Garmin
(example /Garmin/DeviceConfig_MP3_Enabled.xml)
Restart your Nuvi .
Hi Catymag,
Thanks for the quickly reply!
But I already had did this procedure before but didn't worked.
Now I repeated again, without success.... :disapointed:
The folder is the Garmin inside the internal memory, correct? Just copy the .xml files inside the Garmin folder and do a reboot, ok?
More ideas?
[]'s
Normally you should see 3D building . How about some info.Quote:
Originally Posted by rfb [Only registered and activated users can see links. Click Here To Register...]
1). Map info page :: 3D map
2). Inventory page :: show 3790 ?
3). How about 3D-Terrain view (and other features ) ?
4). Did you do H/R ?
Check what do you have in .System\Diag\html
you should have this:
[Only registered and activated users can see links. Click Here To Register...]