Printable View
Hi irresistiQuote:
Originally Posted by irresisti [Only registered and activated users can see links. Click Here To Register...]
Could you please let me know if gps can show thai font or not?
I am still at the point that thai font cannot show in my gps.
I have not tryed it yet. I only use the English map, But try this files.Quote:
Originally Posted by shirobomb [Only registered and activated users can see links. Click Here To Register...]
Just put the Keyboards folder under the main dir in your device and the text also in the main dir of your device. and the BIN file must be in .system\ExtData
[Only registered and activated users can see links. Click Here To Register...]
OK I have tested it all. My device has Thai Keyboard and Thai Menu and Thai Voice. only thai map not tested yet.
I think it must work on your device to. Just put the files I send before on your device, I think the best thing to do after that is Hard Reset. Turn the device of and keep holding the right bottom and power it on. It will then ask you to do a restore. After the restore it will ask you your country again. I chose Thai there and maybe that is what you need to do.
My device is now both Thai and English.
My own gps can show Thai fonts in POIs and I did not do anything special.
1.) Put your finger in top left side of screen and hold.Quote:
Originally Posted by Torujung [Only registered and activated users can see links. Click Here To Register...]
2.) Whit other hand connect nuvi to PC and stil push top left screen
3.) Run updater.exe and select USB (stil push uper left)
4.) Click ok and wait to show on the screen LOADER (now you can remove your finger)
I have a similar problem.
I tried to update nuvi 1200T with the newest CNE maps, but Garmin MapUpdater started software update first. After this update my nuvi shows only a Garmin logo.
I cannot access it as external disk, but it is recognised by WebUpdater and myDashboard (but only when I connect in this mode where you have to press upper left corner and power on). WebUpdater can see the device, but fails when it comes to updating (either 'connection problem' or 'update file corrupted' message).
I tried updater.exe and it seems to work - it shows progress bar etc. - but when the device reboots nothing is changed. All I can see is the logo.
Any ideas what's wrong and how to fix it?
If you dont have a have MTK chip flash it with updater and this
1200_sw219.rgn (14,8 MB)
[Only registered and activated users can see links. Click Here To Register...]
then update to the latest sw with webupdater
or you can try to make a cure by yourself to avoid it loads the corrupt gupdate.
[Only registered and activated users can see links. Click Here To Register...]
and load .rgn with updater
Thank you so much! It worked :)
After the update my nuvi started and said something about GIR version mismatch, but the device was visible as a external disk. Then I loaded 5.30 firmware - nuvi didn't see installed maps and languages, then reset and another update - nuvi starts, everything loads fine :D Yay!
when I try to turn on my garmin 255w, it appeared the screen of garmin and reset indefinitely.
I went online and read several posts (like this in portuguese:
[Only registered and activated users can see links. Click Here To Register...])
I downloaded the g7towin, and information from my gps were as follows:
nüvi 2 Series Software Version 6.10 ID: 827
Unit ID: 3718 ....... etc. .....; USB Comm via Bulk Pipe
so i download the package to "Nuvi 2X5 ID 827" from
[Only registered and activated users can see links. Click Here To Register...]
i run the update.exe and it updated my garmin, but when I finished the update and restart my garmin, i have the same reset indefinitely ... he was still showing the logo of garmin and resetting the device.
so, i try others firmwares...until I installed one of them (can not remember which it was) and Now, when running g7towin,
it's the following error message:
USB Error: open_garmin_usb: failed getting USB handle
ID: 0 Unit ID: 0 USB via Bulk Pipe Comm
and now i cant access by preboot mode.
=(
how i can update/re-write firmware with this usb error and if i cant access my garmin by preboot mode?
(sorry for my bad english)
Adriano
You killed your garmin 255w. If you install FW of version 460 on device with FW with version above 5.10 is always lethal case. If it is not so I am just glad that!
