New Navcores v9.541 & /9.501 released for many NAV2 devices

[biggerdave]

[Only registered and activated users can see links. ] :-



VERSION 9.541
Released on 19 December 2018 This update applies to: XXL Classic, ONE IQ Routes, XL IQ Routes, XL IQR2 / XL Classic, GO 750, GO 750 LIVE, GO 950, GO 950 LIVE, GO 540 LIVE, GO 740 LIVE, GO 940 LIVE, GO 530, GO 630, GO 730, GO 930, GO 720, GO 520, GO 920, EASE, ONE 140, Start

Maintenance release.


...so remember if you do take this TTHome mandatory update you'll need to patch this (as all previous navcore versions) to be able to run pirate maps etc!

Direct links:-
[Only registered and activated users can see links. ]
[Only registered and activated users can see links. ]

[biggerdave]

FINALLY they admit the reason for this:-

The update which covers the fix for the GPS roll-over was included in a firmware released last year....

[Eisenhart]

What's the difference between LE.cab and GO.cab?

[biggerdave]

Logically, the GO version is for all those device called GO... & the LE is for the rest:-
This update applies to: XXL Classic, ONE IQ Routes, XL IQ Routes, XL IQR2 / XL Classic, GO 750, GO 750 LIVE, GO 950, GO 950 LIVE, GO 540 LIVE, GO 740 LIVE, GO 940 LIVE, GO 530, GO 630, GO 730, GO 930, GO 720, GO 520, GO 920, EASE, ONE 140, Start

[biggerdave]

See here for possible fix to the time reset problem (and not just for Truck Navcore):- [Only registered and activated users can see links. ]

[pe1agp]

Dutch
De oplossing voor de TomTom Truck met behulp van de officiële of gewijzigde 9.702-navcore is heel eenvoudig:
vervang gewoon een enkel bestand (de "glgps" in de map "bin").
Het bestand \ bin \ glgps van 9.702 moet worden vervangen door dat van 9.541.
Alles werkt dan normaal op GO x20, x30, x40 en x50.

Ik heb met succes getest op de volgende modellen:
GO 920, GO 630, GO 730, GO 930, GO 540, GO 940, GO 750, GO 950 en GO 9000.
Ik heb geen testeenheid om te testen.

N. B. Dezelfde wijziging werkt ook voor navcores 9.510 en 9.401 (ik heb het geprobeerd).
Het is interessant voor de Fransen, omdat de 9.401 de laatste navcore is vóór 9.510, die altijd de
exacte positie van de radars in Frankrijk aangeeft na de wet van 5 januari 2012 die het verbiedt.

English
The solution for the TomTom Truck using the official or modified 9.702 navcore is very simple:
just replace a single file (the "glgps" in the "bin" folder).
It is necessary to replace the file \bin \glgps of 9.702 by that of 9.541.
Everything then works normally on GO x20, x30, x40 and x50.

I have successfully tested on the following models:
GO 920, GO 630, GO 730, GO 930, GO 540, GO 940, GO 750, GO 950 and GO 9000.
I do not have a One to test.

N. B. The same modification also works for navcores 9.510 and 9.401 (I tried).
It is interesting for the French, because the 9.401 is the last navcore before 9.510 which always indicates
the exact position of the radars in France after the law of January 5th, 2012 which forbids it.


Note:
It work for sure with many other Navcore's and devices too


All credits to Charlie62

[Tarassboulba]

It works on Go710 ? (bootloader 5.5244)

And how to install it please.

I'm a newbie.

Thanks

Not working on Go 710

Freeze on startup every time

[biggerdave]

How about a hard reset (paperclip in the bottom reset hole) and/or holding the power button down until you hear the drums and/or running clearflash.exe 3 times allowing a reboot after each run from here [Only registered and activated users can see links. ]

[rusigor]

Freeze on startup every time

Try this one - [Only registered and activated users can see links. ]

PS I use similar (9541-DSA-32mb) on my old Go700 - works well, whilst official 9541 stuck on startup screen (as yours does).

[Tarassboulba]

How to install it? It's a .dlc