Welcome guest, is this your first visit? Click the "Create Account" button now to join.
Page 8 of 13 FirstFirst ... 678910 ... LastLast
Results 71 to 80 of 125
  1. #71
    Kenwood Moderator ORAK's Avatar
    Join Date
    Oct 2009
    Location
    Romania
    Age
    47
    Posts
    146
    Rep Power
    343

    Tool Kenwood DNX9260BT pre-boot mode.

    Quote Originally Posted by mylona79 View Post
    does anybody know for sure how to enter in pre boot mode?
    Everything you do, you do so at your own responsibility.
    I am not responsible for yours errors, mistakes and damage created and ......


    Tested by me and it works on Kenwood DNX9260BT with navigation module W02-5378-45.
    To enter pre-boot mode, follow photos.


    [Only registered and activated users can see links. ] [Only registered and activated users can see links. ]

    [Only registered and activated users can see links. ] image

    Attention!!!!

    These wires must be very thin and very flexible.

    Even less than what I used here: [Only registered and activated users can see links. ] [Only registered and activated users can see links. ]

    Please be very carefull with solder these wires.
    Soldering contacts are very small and fragile.
    Do not use a high temperature solders.
    You will need a skill for electronics.
    If you do not have this, you will destroy the module, irremediably.

    Like in this picture:

    [Only registered and activated users can see links. ]

    If you happened so, you still have a chance, one last chance.
    Go outside only one wire, on that you put it to ground in outside, (chassis housing or - 12V), to enter pre-boot mode.
    Like in this picture.:

    [Only registered and activated users can see links. ]

    ......... The discussion will continue in post #73 and #75.


    Everything you do, you do so at your own responsibility.
    I am not responsible for yours errors, mistakes and damage created and ......
    Last edited by ORAK; 2nd June 2015 at 03:48.
    By ORAK (ex baghdadvaio)
    ______________________________________________________
    |__________00 01 02 03 04 05 06 07__08 09 0A 0B 0C 0D 0E 0F |
    |00000000__4E 65 67 6F 65 73 63 75__20 56 69_6F 72 65 6C 20 |

    Garmin Nüvi 755LMT -->> Garmin Nüvi 3590LMT

  2.    Advertissements


  3. #72
    Member + mylona79's Avatar
    Join Date
    May 2007
    Location
    Cyprus
    Age
    38
    Posts
    68
    Rep Power
    0

    Default

    from there how to proceed ?

  4. #73
    Kenwood Moderator ORAK's Avatar
    Join Date
    Oct 2009
    Location
    Romania
    Age
    47
    Posts
    146
    Rep Power
    343

    Rom Recovery the module navigation Kenwood DNX9260BT Part 1

    Quote Originally Posted by mylona79 View Post
    from there how to proceed ?
    Everything you do, you do so at your own responsibility.
    I am not responsible for yours errors, mistakes and damage created and ......


    And to me, happened same thing.
    The representative Kenwood asked me 650 euros for new Navigation Module or 250 to repair my Navigation Module.

    Attention !!!
    Do not delete the files
    img_rsrc.gir and GarminDevice.xml from the memory of Garmin.
    (You can delete all the rest)

    Do not format the memory of
    Garmin.
    If you accidentally formatted memory, before disconnecting from the PC recopied file img_rsrc.gir.

    Download img_rsrc.gir :
    Attention !!!
    This img_rsrc.gir
    is Only for DNX9260BT and DNX7260BT.
    Do not use to other devices.


    [Only registered and activated users can see links. ]

    And put in:
    x:\Garmin\img_rsrc.gir

    Attention !!!

    - Point 1A.

    Always make a backup of internal memory with all files and folders.
    Do not forget to make the System files and folders visible from Folder Options.

    Start/Control Panel/Appearance and Personalization/Folder Options
    (Windows 7 Ultiamate)
    [Only registered and activated users can see links. ]

    For backup use USB Image Tool.
    Download:

    [Only registered and activated users can see links. ]

    1.[Only registered and activated users can see links. ] 2.[Only registered and activated users can see links. ] 3.[Only registered and activated users can see links. ]

    4.[Only registered and activated users can see links. ] 5.[Only registered and activated users can see links. ] 6.[Only registered and activated users can see links. ]


    - Point 2A
    If you have deleted the file img_rsrc.gir or format the memory of Garmin.
    After restart Kenwood DNX9260BT, the app Garmin will not start and you can not access the internal memory.

    1.[Only registered and activated users can see links. ] 2.[Only registered and activated users can see links. ] 3.[Only registered and activated users can see links. ]

    Garmin will be recognized by PC just so in Device Manager:

    [Only registered and activated users can see links. ]


    - Point 2B
    To make Garmin functional we have to use GarminCure3 for dnx7x60_9x60_380 without pk_files66_zip with Updater_exe.

    Download GarminCure3 for dnx7x60_9x60_380 without pk_files66_zip with Updater_exe.rar:

    http://www38.zippyshare.com/v/8EXqsLBF/file.html


    1.[Only registered and activated users can see links. ] 2.[Only registered and activated users can see links. ] 3.[Only registered and activated users can see links. ] 4.[Only registered and activated users can see links. ]

    5.[Only registered and activated users can see links. ] 6.[Only registered and activated users can see links. ] 7.[Only registered and activated users can see links. ] 8.[Only registered and activated users can see links. ]

    We need to reset Kenwood DNX9260BT.

    [Only registered and activated users can see links. ]

    After reset Kenwood DNX9260BT you have access to the internal memory of Garmin.

    [Only registered and activated users can see links. ]


    - Point 2C
    Now we have let's make to restore internal memory Garmin.
    (or copied all the files and folders, or copied file img_rsrc.gir back to the memory Garmin)
    For this step we need USB Image Tool.

    1.[Only registered and activated users can see links. ] 2.[Only registered and activated users can see links. ] 3.[Only registered and activated users can see links. ]

    4.[Only registered and activated users can see links. ] 5.[Only registered and activated users can see links. ] 6.[Only registered and activated users can see links. ] 7.[Only registered and activated users can see links. ]

    Now restore is complete, disconnect from PC and we need to reset Kenwood DNX9260BT.

    [Only registered and activated users can see links. ]

    [Only registered and activated users can see links. ]

    Everything you do, you do so at your own responsibility.
    I am not responsible for yours errors, mistakes and damage created and ......
    Last edited by ORAK; 2nd March 2016 at 09:50.
    By ORAK (ex baghdadvaio)
    ______________________________________________________
    |__________00 01 02 03 04 05 06 07__08 09 0A 0B 0C 0D 0E 0F |
    |00000000__4E 65 67 6F 65 73 63 75__20 56 69_6F 72 65 6C 20 |

    Garmin Nüvi 755LMT -->> Garmin Nüvi 3590LMT

  5. #74
    Member + mylona79's Avatar
    Join Date
    May 2007
    Location
    Cyprus
    Age
    38
    Posts
    68
    Rep Power
    0

    Default

    my friend i accidentally deleted my files and folders in garmin. is it possible pls you can send me a copy here or in my email? i will appreciate it.

  6. #75
    Kenwood Moderator ORAK's Avatar
    Join Date
    Oct 2009
    Location
    Romania
    Age
    47
    Posts
    146
    Rep Power
    343

    Rom Recovery the module navigation Kenwood DNX9260BT Part 2

    Everything you do, you do so at your own responsibility.
    I am not responsible for yours errors, mistakes and damage created and ......


    This is continuing discussion from the post #71 and #73 ..............

    I fired two wires apart and I remounted everything back.
    [Only registered and activated users can see links. ]

    [Only registered and activated users can see links. ]

    The next step after reset Kenwood DNX9260BT I put together the 2 wires for pre-boot mode and connect to PC via USB.

    [Only registered and activated users can see links. ]

    We have to do updates with the software to version "dnx7x60_9x60_380" without "pk_files66.zip" with Updater.exe

    [Only registered and activated users can see links. ]

    1.[Only registered and activated users can see links. ] 2.[Only registered and activated users can see links. ] 3.[Only registered and activated users can see links. ]

    4.[Only registered and activated users can see links. ] 5.[Only registered and activated users can see links. ] 6.[Only registered and activated users can see links. ] 7.[Only registered and activated users can see links. ]


    After finishing firmware update I disconnected the two wires for pre-boot mode and I have isolated separately and we left out for any eventuality.
    Disconnect from PC and we need to reset Kenwood DNX9260BT.

    Then I redesigned settings and started the Garmin normal.
    But it is not fully functional The longer it takes only one step.

    1.[Only registered and activated users can see links. ] 2.[Only registered and activated users can see links. ] 3.[Only registered and activated users can see links. ]

    Now the last step.
    On an SD card formatted in FAT32 with RMPrepUSB.

    [Only registered and activated users can see links. ]


    1.[Only registered and activated users can see links. ] 2.[Only registered and activated users can see links. ]

    3.[Only registered and activated users can see links. ] 4.[Only registered and activated users can see links. ]

    I put firmware update DNX7x60_9X60_431 original and unchanged.
    SD:\Garmin\GUPDATE.GCD

    [Only registered and activated users can see links. ]
    [Only registered and activated users can see links. ]

    We need to reset Kenwood DNX9260BT
    I put SD card in card reader from Kenwood DNX9260BT.
    The update went well by SD card reader, Garmin has become normal and functional.

    [Only registered and activated users can see links. ]

    So we saved between 250 and 650 euros and I'm very happy.
    Thanks to everyone who gave me the information, applications and ...... more.

    P.S.
    do not use Garmin Cyclops, leading to reset Garmin application.

    Everything you do, you do so at your own responsibility.
    I am not responsible for yours errors, mistakes and damage created and ......


    I did everything on my own responsibility.
    I did not have what to lose.
    I risked and ..... I won.
    To me it functioned.

    [Only registered and activated users can see links. ][Only registered and activated users can see links. ]
    [Only registered and activated users can see links. ][Only registered and activated users can see links. ]
    Last edited by ORAK; 2nd March 2016 at 10:06.
    By ORAK (ex baghdadvaio)
    ______________________________________________________
    |__________00 01 02 03 04 05 06 07__08 09 0A 0B 0C 0D 0E 0F |
    |00000000__4E 65 67 6F 65 73 63 75__20 56 69_6F 72 65 6C 20 |

    Garmin Nüvi 755LMT -->> Garmin Nüvi 3590LMT

  7. #76
    Navigation software Moderator

    kunix's Avatar
    Join Date
    Sep 2011
    Location
    Belarus
    Posts
    1,041
    Rep Power
    601

    Default

    You've got an easy-to-understand message from catymag.
    Quote Originally Posted by catymag View Post
    Cure is useful if pc doesn't recognize your device and it's made to format or to delete problematic files prevent Garmin to boot.
    And I told you this one more time
    Quote Originally Posted by kunix View Post
    mylona79
    So you can access your device in mass storage mode. This means that either GarminCure3 worked fine or you don't need it at all.
    And I didn't really ask you to use GarminCure3, i just helped you to flash GarminCure3-ed firmware over USB.
    Quote Originally Posted by kunix View Post
    Please use the following GCD file with GarminCure3 (if you ever need it): [Only registered and activated users can see links. ]
    So, in conclusion, GarminCure3 was not required at all, and you've been told this several times.
    And nevertheless, you used it. I admit that without my modified GCD you wouldn't be able to flash GarminCure3-ed firmware. But you were the one who pushed the trigger, not me.

    Now we have ORAK trying to help you with entering pre-boot mode and flashing the original firmware.
    And instead of following his very well explained advices you're doing some weird ****.

  8. #77
    Junior Member
    Join Date
    Apr 2015
    Location
    Swiss
    Posts
    4
    Rep Power
    0

    Default

    Hello, great job, really !!! I found solution of pre-boot only on your forum,
    I have the same DNX9260BT, W02-5378-25.

    one small question - I made backup before install of cure3 firmware, but as "copy of folders and files", not as image. should it be working ?
    Last edited by ulanov; 1st June 2015 at 21:51.

  9. #78
    Garmin/GPS Systems GMod.

    Neil's Avatar
    Join Date
    Aug 2011
    Location
    Oz.
    Posts
    7,401
    Rep Power
    1434

    Default

    G'day ulanov, welcome to GPSPower.
    Quote Originally Posted by ulanov View Post
    .......... I made backup before install of cure3 firmware, but as "copy of folders and files", not as image. should it be working ?
    If you could make a backup of the internal files system then YOUR device didn't need a cure firmware because it could still be seen in MSM. So why flash Cure3?

    Please explain EXACTLY what the problem is. We have experts posting in this thread presently, and there's not many ppl who understand the peculiarities of both the hardware and software of the Kenwood-Garmin marriage. However there's even fewer ppl in the world with psychic powers [Caty does go close though] .
    'Thanking Posts' are banned. To thank someone, and/or to see hidden links and content, use the [Only registered and activated users can see links. ] button below left of the helpful post then refresh your browser [F5 key]. 'Thanking Posts' are banned.
    Please don't spam. Posts serving no purpose other than to thank or to ask about hidden links are trashed or deleted, it's GPSPower's policy. Please don't spam.
    [Only registered and activated users can see links. ] should make their first post as a new Intro Thread in [Only registered and activated users can see links. ].

  10. #79
    Kenwood Moderator ORAK's Avatar
    Join Date
    Oct 2009
    Location
    Romania
    Age
    47
    Posts
    146
    Rep Power
    343

    Default

    Yes, of course, try and you'll see I'm right.
    By ORAK (ex baghdadvaio)
    ______________________________________________________
    |__________00 01 02 03 04 05 06 07__08 09 0A 0B 0C 0D 0E 0F |
    |00000000__4E 65 67 6F 65 73 63 75__20 56 69_6F 72 65 6C 20 |

    Garmin Nüvi 755LMT -->> Garmin Nüvi 3590LMT

  11. #80
    Junior Member
    Join Date
    Apr 2015
    Location
    Swiss
    Posts
    4
    Rep Power
    0

    Default

    thank you.

    I bought used device on ebay with remark "map not work" - PC doesn't see Garmin folder, Navi screen is black.

    I found one solution: to load cure3, then format recognised flash and load original firmaware in pre-boot again.
    ok, till p.3 everything was fine. and I hoped to switch device in per-boot with SRC + quieter + Reset or SRC mode + ATT + RESET
    but unsuccessfully
    Last edited by ulanov; 1st June 2015 at 21:52.

 

 
Page 8 of 13 FirstFirst ... 678910 ... LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.