Welcome guest, is this your first visit? Click the "Create Account" button now to join.
Page 8 of 58 FirstFirst ... 67891018 ... LastLast
Results 71 to 80 of 578
  1. #71
    Master
    Join Date
    Nov 2010
    Location
    Posts
    203
    Rep Power
    41

    Default

    for the bricked unit, after a week battery lost it's voltage.
    Tried to link with external power supply but no luck for my case.

  2.    Advertissements


  3. #72
    Member
    Join Date
    Sep 2010
    Location
    colombia
    Posts
    28
    Rep Power
    0

    Default

    Hi to everyone, thanks to this post iīve been able to make my Nuvi 1300 work again. thanks a lot to everyone for sharing your knowledge. Now, iīm stuck with a problem: when i run pgarmincure3 in core mode i can see my nuvi in my computer, iīm able to update it with webupdater, upload maps with mapsource, etc. but, offocurse my nuvi wont boot. After flashing again with original firmware my Nuvi boots normally but now i canīt see it anymore in my computer or use it with mapsource or webupdater. Any ideas?

    any help will be fully apreciated.

    thanks again.

  4. #73
    Navigation software expert Kanopus's Avatar
    Join Date
    Jan 2010
    Location
    Internet
    Posts
    481
    Rep Power
    249

    Default

    If your nuvi boots in navigation mode, when connected to PC, then you can have bad USB cable or USB socked in nuvi.
    Thanks, Kanopus

  5. #74
    Member
    Join Date
    Sep 2010
    Location
    colombia
    Posts
    28
    Rep Power
    0

    Default

    Quote Originally Posted by Kanopus View Post
    If your nuvi boots in navigation mode, when connected to PC, then you can have bad USB cable or USB socked in nuvi.
    i donīt think so, itīs the same cable and port i use when itīs recognized after cure firmware. Also these are the same i use to flash the firmware, the problem is after flashing original firmware. I have to run garmincure with cure firmware, upload maps or anythig else, then rerun garmincure with original firmware to make it boot... but then itīs no longer detected by pc...
    Last edited by scorpion-4x4; 7th April 2012 at 00:15.

  6. #75
    Navigation software Moderator

    kunix's Avatar
    Join Date
    Sep 2011
    Location
    Belarus
    Posts
    1,038
    Rep Power
    601

    Default

    I've never encountered such weird behaviour....
    Can you check if the PC detects any new devices when you connect your nuvi with ORIGINAL firmware (open device manager and then connect the cable)?
    Is it possible that your cable is a Garmin Service USB cable?

  7. #76
    Member
    Join Date
    Sep 2010
    Location
    colombia
    Posts
    28
    Rep Power
    0

    Default

    Quote Originally Posted by kunix View Post
    I've never encountered such weird behaviour....
    Can you check if the PC detects any new devices when you connect your nuvi with ORIGINAL firmware (open device manager and then connect the cable)?
    Is it possible that your cable is a Garmin Service USB cable?
    No, my pc doesnīt detect anything, itīs like me connecting the bare cable... iīve tried several cables with same result. i donīt what else to do...

  8. #77
    Navigation software expert

    lolypop000's Avatar
    Join Date
    May 2010
    Location
    EU
    Posts
    2,925
    Rep Power
    849

    Default

    Try this,this help me on problem like yours.

    Flash with cure FW and then create backup of your nuvi (dont forget hiden folder .System)

    Format nuvi to FAT32

    Add back your backup and turn nuvi on

    Go to hiden menu over cockpit and clear nonvol.

  9. #78
    Member
    Join Date
    Sep 2010
    Location
    colombia
    Posts
    28
    Rep Power
    0

    Default

    Quote Originally Posted by lolypop000 View Post
    Try this,this help me on problem like yours.

    Flash with cure FW and then create backup of your nuvi (dont forget hiden folder .System)

    Format nuvi to FAT32

    Add back your backup and turn nuvi on

    Already did this, same behavior.

    Quote Originally Posted by lolypop000 View Post
    Go to hiden menu over cockpit and clear nonvol.
    can you explain this? I donīt really understand what to do.

    Thanks

  10. #79
    Navigation software Moderator

    kunix's Avatar
    Join Date
    Sep 2011
    Location
    Belarus
    Posts
    1,038
    Rep Power
    601

    Default

    scorpion-4x4
    Can you also go to the battery menu (press and hold the battery icon until the menu appears) and tell us which captions change there when you connect the USB cable?

  11. #80
    Member
    Join Date
    Sep 2010
    Location
    colombia
    Posts
    28
    Rep Power
    0

    Default

    Quote Originally Posted by catymag View Post
    hard reset Nuvi clearing non vol in Debugging menu :hold your finger in Volume page, upper right corner ,landscape position, go to Developer infos/Non vol Statistics, press the 3 Bars menu and Clear Non Vol.
    well, did that, same behaviour, still not detected. Any other ideas?

    thanks

    Quote Originally Posted by kunix View Post
    scorpion-4x4
    Can you also go to the battery menu (press and hold the battery icon until the menu appears) and tell us which captions change there when you connect the USB cable?
    USB Device changes from no cable detected to Power Cable.
    I limit USB changes from unknown to 1A
    Power Source changes from Bat to Ext

 

 
Page 8 of 58 FirstFirst ... 67891018 ... LastLast

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.