Welcome guest, is this your first visit? Click the "Create Account" button now to join.
Page 45 of 76 FirstFirst ... 35434445464755 ... LastLast
Results 441 to 450 of 755
  1. #441
    Junior Member
    Join Date
    Dec 2009
    Location
    US
    Posts
    2
    Rep Power
    0

    Default

    My Steps For Permanently Activating Total Traffic Network and NAVTEQ On GTM 20 and Nuvi 880

    Please note that I don't check these boards often so if this does not work for you, I'm sorry, YMMV. I'm just sharing what worked for me in the hopes that they will not have to read through the hundreds of pages that I did on Noeman.org I hope this works for other Nuvi models other than mine, as I expect it should since the problematic device is the GTM 20.

    Please read all the way through first. If you're confused by the instructions, I'm sure others can explain Jetmouse 1.3 v Jetmouse 1.5; 0, 0, 0 v 0, 0, 1; etc.

    To me, these seem to be the important details:
    1) Make sure the Mapset is named "All" exactly with the lowercase l's and no quotes. Not sure why but it's something I came across. Therefore, Map Info will read "CN North America NT 2013.10" Next Line: "All" The mapset name might have been a problem for some.
    2) Do a complete power cycle. The Nuvi provides power to the GTM 20, even if you unplug the GTM 20 from the socket. I also took out the battery on the Nuvi. A full 10 second wait is recommended. So turn off Nuvi, take out battery, unplug GTM 20, disengage GTM 20 from Nuvi. Incomplete power cycling is almost surely the problem for some.
    3) Must turn off TTN USA and CAN.
    4) Must download and use Jetmouse 1.3 Modded for Traffic. Is this the magic step? I don't know as the discussion included hex code explanations of why 4095 was the important number.
    5) Must add both TTN USA and CAN.

    I think some of the steps are redundant. NAVTEQ seems to hold no matter what so adding NAVTEQ CAN is probably not necessary. Adding TTN USA, power cycling and then adding TTN USA and CAN. Probably also redundant. I just took everything that worked for others and threw it in there. FastIMG Unlocker? Probably not related but given the oddity about the Mapset name, who knows?

    I followed these steps and I now have TTN and NAVTEQ Lifetime with No Ads on my Nuvi 880. Again, YMMV. Good luck!

    Steps
    1) Install Maps Directly from Mapsource 6.16.3
    2) Rename the Mapset “All” (The First Letter Caps, The Last Two Lower Case)
    3) Copy IMG File from Device to PC
    4) Run FastIMG Unlocker 2.1
    5) Copy IMG File from PC to Device
    6) Add *.unl File
    7) 28935, 0, 0, 0 (Turn Off NAVTEQ USA With Code Generated By Jetmouse 1.5 - Garmin Keygen v1.5 + CF.exe)
    8) Power Cycle (Turn Off Nuvi, Unplug GTM 20 From Power, Undock Nuvi From GTM 20, Pull Out Nuvi Battery, Check To Make Sure All Lights Off On GTM 20, Wait 10 Seconds)
    9) 28935, 0, 0, 0 (Turn Off NAVTEQ USA Again)
    10) 31751, 0, 0, 0 (Turn Off NAVTEQ CAN)
    11) Power Cycle
    12) 28992, 0, 0, 0 (Turn Off TTN USA)
    13) Power Cycle
    14) 28992, 0, 0, 0 (Turn Off TTN USA Again)
    15) 31808, 0, 0, 0 (Turn Off TTN Canada)
    16) Power Cycle
    17) 4095, 0, 0, 1 (Turn On TTN USA With Code Generated By Jetmouse 1.3 Modded For Traffic - jmgkg13modTMCExp.exe)
    18) Power Cycle
    19) 28992, 0, 0, 1 (Turn On TTN USA)
    20) 31808, 0, 0, 1 (Turn On TTN Canada)
    21) Power Cycle
    22) 28935, 0, 0, 1 (Turn On NAVTEQ USA)
    23) 31751, 0, 0, 1 (Turn On NAVTEQ CAN) This is the only optional step. TTN needs to be turned on both for USA and CAN so wanting to be safe, I entered the code for NAVTEQ CAN. In Southern California, you need a GPS signal and a connection to Canada to activate NAVTEQ CAN. I entered the Turn Off Code for NAVTEQ CAN and all seems to be fine. I guess you would turn it on if you're near the Canadian border but if you're not, whether it's on the GTM 20 or not does not seem to affect NAVTEQ's USA service.
    24) Power Cycle

    Please note that I did not ever use the same code twice. I generated different turn off and on codes for everything. So, you're spending some quality time in Jetmouse...

    Was it worth all this effort? The GTM 20 cost me less than $20 shipped on eBay and it's kind of nice that my old Nuvi has both traffic and voice recognition, helpful for when I'm using my iPhone for other tasks. However, the quality of the traffic reports from either Clear Channel/TTN and Navteq is clearly inferior to what a dozen apps on the iPhone, including Google Maps, can provide. If the CC/TTN doesn't stick for you, I'd honestly tell you that you're not losing much. And that's saying a lot in Los Angeles, where you'd think the quality of the traffic reports would be better.

    Good luck all :-)
    Last edited by KLancelot; 18th June 2012 at 00:15.

  2.    Advertissements


  3. #442
    Member +
    Join Date
    May 2010
    Location
    U.S.A.
    Posts
    32
    Rep Power
    7

    Default

    I have tried to follow your instructions for obtaining an unlock code to obtain traffic capability. I have a Nuvi 760 and a GTM 20 traffic receiver. When I go to ADD in the traffic menu I do NOT get a traffic receiver ID. All I get is my unit number. Am I supposed to get an ID number from the GTM 20 itself? Even if I were to obtain a traffic receiver ID number, where do I input it in the Jetmouse Keygen? There is only a Unit ID entry. Is that supposed to be used to input the ID's for both the Nuvi and the GTM 20? I am confused.

  4. #443
    ☼ADMIN☼
    catymag's Avatar
    Join Date
    Nov 2007
    Location
    light side
    Posts
    23,614
    Rep Power
    5322

    Default

    Read instructions in post n1 how to create the .unl code. To get the TMC receiver ID, the TMC receiver must be connected
    [Only registered and activated users can see links. ]
    [Only registered and activated users can see links. ]

    [Only registered and activated users can see links. ]
    You have to navigate to get to the good.
    Nuvi1250/Nuvi 34xx/Nuvi 2200/Nuvi 66/Oregon 600/Galaxy S5 MM 6.0.1/TomTom GO/iGO Nextgen Avic,Basar,Isr.Gift/Navigon
    Please don't flood my pm box with questions you can post on forum!! You won't hear back from me.

  5. #444
    Member +
    Join Date
    May 2010
    Location
    U.S.A.
    Posts
    32
    Rep Power
    7

    Default

    As I mentioned in my previous post, the TMC Receiver is connected. I get no receiver ID. When I try to ADD a subscription it tells me to go to the garmin website and provide the unit id number being displayed. The only number that is displayed is my Nuvi ID but no traffic receiver ID number. Again, the GMT 20 is connected. Both lights on the GMT 20 are lit. So I don't know what to try next. After I click NEXT on the Nuvi it prompts me for the unlock code given to me by Garmin. Again, there is never Receiver ID displayed.

  6. #445
    Member +
    Join Date
    Dec 2009
    Location
    Tristan da Cunha
    Posts
    30
    Rep Power
    0

    Default

    Quote Originally Posted by OneBadTexican View Post
    As I mentioned in my previous post, the TMC Receiver is connected. I get no receiver ID. When I try to ADD a subscription it tells me to go to the garmin website and provide the unit id number being displayed. The only number that is displayed is my Nuvi ID but no traffic receiver ID number. Again, the GMT 20 is connected. Both lights on the GMT 20 are lit. So I don't know what to try next. After I click NEXT on the Nuvi it prompts me for the unlock code given to me by Garmin. Again, there is never Receiver ID displayed.
    Register The GMT20 at the MyGarmin with its serial number, once registered you'll get the Receiver ID from your units summary.

  7. #446
    Junior Member
    Join Date
    Dec 2009
    Location
    US
    Posts
    2
    Rep Power
    0

    Default

    This thread is a sticky.

    The very first post in this thread by Catymag is very useful. Yes, you need the GTM 20's ID number.

    From the first post:
    "Each TMC receiver has its own 10-digit ID.
    This one is another number then nuvi ID, you can find it only when nuvi is connected to TMC receivers. Go to menu Tools, Settings, Traffic, Subscriptions, Add and see message containg your TMC receiver ID.

    Each subscription has its FID, PID, RgnID an VenID, similarly to Garmin map product. All known subscription ID are gathered at the end of this post.

    Both values, TMC ID and subscription ID can be used to generate unlock code. Use [Only registered and activated users can see links. ] for creating unlock codes.

    Start keygen, insert TMC ID into field Enter your Unit ID here then go to Select Map Product and choose Custom Mapset. In Custom Mapset window check Enable additional fields and fill all 4 values for FID, PID, RgnID, VenID.

    You should manualy rewrite unlock code to TMC receiver in the same menu you used to find TMC receiver ID."

    My original post should have included instructions to always read the first post in a sticky thread. Please note you'll need to Google for the two different versions of Jetmouse required. Good luck!

  8. #447
    Master
    Join Date
    Feb 2011
    Location
    USA (East)
    Posts
    95
    Rep Power
    57

    Default

    Quote Originally Posted by OneBadTexican View Post
    I have tried to follow your instructions for obtaining an unlock code to obtain traffic capability. I have a Nuvi 760 and a GTM 20 traffic receiver. When I go to ADD in the traffic menu I do NOT get a traffic receiver ID. All I get is my unit number. Am I supposed to get an ID number from the GTM 20 itself? Even if I were to obtain a traffic receiver ID number, where do I input it in the Jetmouse Keygen? There is only a Unit ID entry. Is that supposed to be used to input the ID's for both the Nuvi and the GTM 20? I am confused.
    I assume you are doing all of this with both the GTM and 760 powered up (you must be to have gotten an ID).

    That ID you got in the ADD Subscription dialog IS the 10 digit unit ID from the GTM 20 (and the ONLY one you need for the kegen). It is NOT the unit ID for your 760.
    If you want the UnitID for the 760 look at
    Tools > Settings > System > About
    and your 760 ID will be in the upper left hand corner. You will see that the 2 UnitID's are different.

    FYI - The GTM 20 UnitID and any subscription Keys you enter are stored in the GTM, none of that data is saved in the GPS which is why A "Traffic Enabled" GTM-20 will then work on any 7xx GPS or any model that is compatable with a GTM-20. The Traffic interface on the 760 is just a mechanism for you (the user) to communicate with the GTM for the purpose of adding or renewing expired subscriptions.
    Last edited by tiger555; 20th June 2012 at 02:16.

  9. #448
    Member +
    Join Date
    May 2010
    Location
    U.S.A.
    Posts
    32
    Rep Power
    7

    Default

    Thank you for your immediate response. You are absolutely right. I got the ID number and used it to generate the traffic codes. I was able to obtain the Navteq code and it works perfectly. Sadly, like everyone on this forum, I have been unable to obtain a code that will last for more than a few seconds for the TMC. There are no specific instructions as to how to obtain a permanent subscription. I have pretty much tried everything except using the modified Jetmouse 1.3 key generator which I can't seem to find anywhere. Perhaps that is the key, I don't know.

    If anyone has the correct instructions to getting it to work properly please let me know. After going through over 400 posts it seems like the original instructions in post No. 1 do not work for the TMC subscription as they have been put up.

  10. #449
    Member +
    Join Date
    May 2010
    Location
    U.S.A.
    Posts
    32
    Rep Power
    7

    Default

    Can anybody provide me a link for the modified for traffice Jetmouse 1.3 key generator? I can't find it anywhere. All torrent downloads but none seem to download the actual program.

  11. #450
    Navigation software expert

    tom1807's Avatar
    Join Date
    Apr 2009
    Location
    APAC
    Posts
    1,100
    Rep Power
    539

    Default

    How much codes did you generate?
    Canada and USA or only USA.
    For making this work, both codes have to be entered

    Edit: Keygen 1.3 attached
    Attached Files Attached Files
    Last edited by tom1807; 20th June 2012 at 03:36. Reason: Added the KG v1.3

 

 
Page 45 of 76 FirstFirst ... 35434445464755 ... LastLast

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.